Difference between revisions of "Eggbot Quality Troubleshooting"

From Evil Mad Scientist Wiki
Jump to: navigation, search
(Our test file)
 
(60 intermediate revisions by 5 users not shown)
Line 1: Line 1:
 +
{{EggBotDocs}}
 +
 
If you are having quality issues with your prints that might be due to a misalignment of some sort, we hope that this guide will help you to find the source of the problem. This guide contains some helpful pictures that show how configuring the EggBot in different ways can produce different outcomes.   
 
If you are having quality issues with your prints that might be due to a misalignment of some sort, we hope that this guide will help you to find the source of the problem. This guide contains some helpful pictures that show how configuring the EggBot in different ways can produce different outcomes.   
  
Line 5: Line 7:
  
 
=== Our test file ===
 
=== Our test file ===
http://shop.emscdn.com/wiki/eggbot/quality/1A.jpg
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/1A.jpg
  
This is the test file that we'll be using for our examples. Note that the print quality is fine and consistent.  The "O's" have closed shapes, the vertical parts are vertical, the horizontal parts are horizontal, the slants of the "W's" have consistent width, and so forth.  (Some of the examples that we'll show later ''do not'' have these properties!)
+
This is the test file that we'll be using for most of the examples. Note that the print quality is fine and consistent.  The "O's" have closed shapes, the vertical parts are vertical, the horizontal parts are horizontal, the slants of the "W's" have consistent width, and so forth.  (Some of the examples that we'll show later ''do not'' have these properties!) Additionally, one should be able to print an example like this ''several times over itself'' without seeing any variation except that the lines appear darker after each successive pass.
  
You can download the example file here. (TODO: ADD LINK)
+
You can download the example file [https://cdn.evilmadscientist.com/wiki/eggbot/quality/calexamples/demo2.zip here].  
  
This was printed with the Deluxe EggBot on a chicken egg with an Ultra Fine Point Sharpie.   
+
This was printed with the [http://shop.evilmadscientist.com/productsmenu/tinykitlist/171-egg-bot Deluxe EggBot] on a chicken egg with an Ultra Fine Point Sharpie.   
The egg was oriented with its "fat" side pointing towards the egg motor (headstock).   
+
The egg was oriented with its "fat" side (the side pointing down in the photo above) pointing towards the egg motor (headstock).   
  
 
The print settings were as follows:
 
The print settings were as follows:
Line 26: Line 28:
 
** Reverse motion of Motor 2 (egg): checked
 
** Reverse motion of Motor 2 (egg): checked
 
** Egg (x) axis wraps around: checked
 
** Egg (x) axis wraps around: checked
** Start with pen centered: checked
 
 
** Return home when done: checked
 
** Return home when done: checked
 
** Enable engraver, if attached: unchecked
 
** Enable engraver, if attached: unchecked
 
** Curve smoothing (lower for more): 0.2
 
** Curve smoothing (lower for more): 0.2
 +
 +
 +
----
  
 
=== Dry pen ===
 
=== Dry pen ===
http://shop.emscdn.com/wiki/eggbot/quality/3A.jpg
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/3A.jpg
 +
 
 +
A common problem that can happen when using old pens, or pens that have been left uncapped is that the pen does not start drawing immediately when you expect it to. It is ''usually'' easy to fix this problem by taking a scratch piece of paper and, right before you start your EggBot, "bleeding" your pen a little on the paper to get the ink flowing again, as shown below. Sharpie pens last approximately forever if treated well; if it doesn't start drawing immediately, you might consider leaving it capped for a few days and trying again, rather than throwing it out. You might also consider wetting the tip with solvent to reconnect the tip to the ink reservoir in the pen. For example, with a Sharpie you would make a small puddle of Isopropyl (rubbing) alcohol on a piece of paper.  Then you would dip the dried-out tip in the puddle, and then try scribbling on the paper to see if ink flow begins.
 +
 
 +
 
 +
https://cdn.evilmadscientist.com/wiki/eggbot/quality/1F-2.jpg
 +
 
  
A common error that tends to happen when using old pens, or pens that have been left un-capped. It is easy to fix this problem by taking a scratch piece of paper and, right before you start your EggBot, bleeding your pen a little on the paper to get the ink flowing again.
 
  
http://shop.emscdn.com/wiki/eggbot/quality/1F-2.jpg
+
----
  
 
=== Alignment of the egg in the egg cups ===
 
=== Alignment of the egg in the egg cups ===
http://shop.emscdn.com/wiki/eggbot/quality/15A.jpg
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/15A.jpg
  
This skewed image is the result of misaligning the egg within the couplers, like so:
+
This skewed image is the result of misaligning the egg within the couplers, like so (exaggerated for clarity):
  
http://shop.emscdn.com/wiki/eggbot/quality/15B.jpg
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/15B.jpg
  
In order to avoid this you should place the egg between the couplers with the egg as flush as you can get it against each coupler. To check if the egg is properly aligned, you twist one of the couplers and watch for any wobbling as the egg rotates. Adjust the egg until there is as little wobbling as possible. It should look something like this:
 
  
http://shop.emscdn.com/wiki/eggbot/quality/1E.jpg
+
In order to avoid this you should place the egg between the couplers with the egg as flush as you can get it against each coupler. To align the egg in place, turn the egg (or the egg coupler) and watch the egg as you turn it. (You may want to use the "Raise pen, turn off motors" option in EggBot Control to make this easy.) Adjust its position until there is as little wobbling as possible; that is, until it doesn't seem to "change shape" as you rotate it.  
  
=== Loose screws ===
 
http://shop.emscdn.com/wiki/eggbot/quality/17A.jpg
 
  
This is the cause of the screw under the pen arm being loose.
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/1E.jpg
  
http://shop.emscdn.com/wiki/eggbot/quality/17B.jpg
+
This egg is properly aligned.
  
If this screw is loose, then the pen arm will move left and right as the pen is dragged across the egg. To check if this screw is loose, try to gently wiggle the pen arm left to right, it should not move at all.
 
  
http://shop.emscdn.com/wiki/eggbot/quality/18A.jpg
 
  
This is what happens when the screw on the back of the distill pen arm is very loose.
+
----
  
http://shop.emscdn.com/wiki/eggbot/quality/18B.jpg
+
=== Loose Eggs & Screws  ===
 +
https://cdn.evilmadscientist.com/wiki/eggbot/quality/17A.jpg
  
This also causes the pen arm to be dragged left to right as the EggBot prints. However, this screw has to be considerably loose to have this kind of result. To check, twist the pen arm left and right. It can move a little, but it should not be able to move when using very gentle force.
+
If your plots look like this, with circles that don't close and differing widths of your letter parts, it likely means that something is loose.  It can be either the egg itself-- slipping in the coupler -- or a loose screw somewhere on the EggBot.   Make sure that the egg has a secure connection to the motor through its coupler, and can't wiggle independently of the motor. And, make sure that the screws on the EggBot are tight and secure (you can also check our troubleshooting guide [http://wiki.evilmadscientist.com/Eggbot_Troubleshooting#precision here]).  
  
http://shop.emscdn.com/wiki/eggbot/quality/19A.jpg
 
  
This happens when the screw that holds the pen in place is loose.
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/17B.jpg
  
http://shop.emscdn.com/wiki/eggbot/quality/19B.jpg
+
If the hex screw below the pen arm's hinge is loose, the pen arm will move left and right as the pen is dragged across the egg. Try to gently wiggle the pen arm left to right. With the exception of the normal flexing of the hinge, it should not move at all.
  
Yet, the screw has to be extremely loose, enough so that the pen can come out of its bindings will printing. To check if the pen is securely fastened, pull up on the pen gently. If it is fastened correctly, then it should not come out.
+
 
 +
https://cdn.evilmadscientist.com/wiki/eggbot/quality/18A.jpg
 +
 
 +
In this case, the screw that mounts the distal pen arm assembly to the proximal pen arm (shown below) was loose, with the kind of poor results that you might expect.
 +
 
 +
https://cdn.evilmadscientist.com/wiki/eggbot/quality/18B.jpg
 +
 
 +
https://cdn.evilmadscientist.com/wiki/eggbot/quality/19A.jpg
 +
 
 +
The plot above-- where the pen is wandering "all over the place" was caused by trying to draw when the screw that holds the pen was loose (about to drop the pen).
 +
 
 +
https://cdn.evilmadscientist.com/wiki/eggbot/quality/19B.jpg
 +
 
 +
To check if the pen is securely fastened, gently try to pull it out.
 +
 
 +
 
 +
----
 +
 
 +
===Pen arm bumps against frame===
 +
https://cdn.evilmadscientist.com/wiki/eggbot/quality/20A.jpg
 +
 
 +
Here is the "diamond" test pattern, shown without any major quality issues (for reference). (You can download the example file [https://cdn.evilmadscientist.com/wiki/eggbot/quality/calexamples/SimpleDiamonds.svg here].)
 +
 
 +
 
 +
 
 +
https://cdn.evilmadscientist.com/wiki/eggbot/quality/21B.jpg
 +
 
 +
https://cdn.evilmadscientist.com/wiki/eggbot/quality/21A.jpg
 +
 
 +
Here is the same pattern, but drawn with the EggBot misaligned such that the starting position of the pen arm was poor and the pen arm bumped into the tailstock of the EggBot while drawing. When the pen arm reaches the end of its range, it may bend and try to continue plotting there, or the motor may skip a step ("cog") and lose alignment.
 +
 
 +
If you are having trouble with hitting the sides, check before plotting -- using the manual ("walk motor") commands if necessary -- to make sure that the pen arm has free travel over the entire range that you intend to use. For more information about positioning the pen arm, see [http://wiki.evilmadscientist.com/Framing_and_Pen_Centering here].
 +
 
 +
If the pen moves but seems to just "fall over" without any resistance, you may still need to [[Making_your_first_plot#Drawing_on_your_Egg|adjust your motor current]].
 +
 
 +
 
 +
----
  
 
=== Vertical position of the pen motor ===
 
=== Vertical position of the pen motor ===
http://shop.emscdn.com/wiki/eggbot/quality/1C-3.jpg
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/1C-3.jpg
 +
 
 +
The pen motor can be moved vertically to adjust the pen arm for drawing on spherical or ellipsoidal surfaces. For drawing on chicken eggs, we normally position the pen motor about in the middle of the slots as shown here. For a sphere, position the motor at the very top of its slots.  For a more elongated egg (maybe a turkey egg?) you may need to go lower yet in the slots.
 +
 
 +
 
 +
https://cdn.evilmadscientist.com/wiki/eggbot/quality/11A.1.jpg
 +
 
 +
If the pen motor is positioned too high in the vertical slots (here, at the top of its slots while printing on a chicken egg), the pen will not make contact over the full surface.  To correct this, lower the motor in the slots.
  
The pen motor can be moved vertically to adjust the pen arm for drawing on oblong surfaces or circular surfaces. Here is an example of the pen motor being in the right position for an egg.
 
  
http://shop.emscdn.com/wiki/eggbot/quality/11A.jpg
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/12B.jpg
  
This misshapen printing is the result of the pen motor being positioned too high.
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/12A.1.jpg
  
http://shop.emscdn.com/wiki/eggbot/quality/12B.jpg
+
Conversely, if the pen motor is too low in its slots, the pen may not make contact at the edges of the plot region.
  
 +
https://cdn.evilmadscientist.com/wiki/eggbot/quality/11B.jpg
  
  
http://shop.emscdn.com/wiki/eggbot/quality/12A.jpg
 
  
This one is because the pen motor was to low
 
  
http://shop.emscdn.com/wiki/eggbot/quality/11B.jpg
+
----
  
 
=== Headstock / Tailstock position ===
 
=== Headstock / Tailstock position ===
http://shop.emscdn.com/wiki/eggbot/quality/1D-3.jpg
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/1D-3.jpg
 +
 
 +
When the headstock is correctly positioned, the shaft of the pen motor points ''directly toward the thickest part'' of the egg (or sphere), as shown above.
 +
 
 +
 
 +
https://cdn.evilmadscientist.com/wiki/eggbot/quality/13B.jpg
 +
 
 +
https://cdn.evilmadscientist.com/wiki/eggbot/quality/14A.1.jpg
 +
 
 +
When the headstock and tailstock are misplaced such that the pen motor is positioned too far to one side, you will find that (1) the pen cannot reach the surface everywhere that you would expect it to and (2) there will be some distortion of the print due to the misalignment. For more on positioning the motor see [http://wiki.evilmadscientist.com/Framing_and_Pen_Centering here].
  
This is the correct position of the headstock and tailstock, where the pen is pointing at the thickest part of the egg.
 
  
http://shop.emscdn.com/wiki/eggbot/quality/13A.jpg
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/14B.jpg
  
This happened when the headstock and tailstock were placed too far to the left, like so.
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/13A.1.jpg
  
http://shop.emscdn.com/wiki/eggbot/quality/13B.jpg
+
A similar condition, in the opposite direction.
  
  
  
http://shop.emscdn.com/wiki/eggbot/quality/14A.jpg
+
----
  
This one when the headstock and tailstock were placed too far to the right.
+
=== Horizontal position of the pen arm===
  
http://shop.emscdn.com/wiki/eggbot/quality/14B.jpg
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/1G.jpg
 +
 
 +
This photo shows the correct orientation for the distal pen arm and pen. Note that when the tip of the pen contacts the egg, the distal pen arm extends out straight and flat, down towards the center of the egg.
 +
 
 +
 
 +
https://cdn.evilmadscientist.com/wiki/eggbot/quality/16B.jpg
 +
 
 +
https://cdn.evilmadscientist.com/wiki/eggbot/quality/16A.jpg
 +
 
 +
If, on the other hand, the pen arm is not horizontal when in the down position, it will cause the drawing to be skewed. (You will see similar types of issues when the pen arm backer is in the wrong position.)
 +
 
 +
 
 +
 
 +
----
  
 
=== Pen arm backer position ===
 
=== Pen arm backer position ===
http://shop.emscdn.com/wiki/eggbot/quality/1B.jpg
 
  
This is the correct position of the backer, where the pen points at the thickest part of the egg.
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/1B.jpg
  
http://shop.emscdn.com/wiki/eggbot/quality/9A-1.jpg
+
When the distal pen arm is correctly positioned-- dead flat when it the pen tip is contacting the egg -- then the tip of the pen should point ''directly down'' and towards the ''thickest part of the egg''. If it does not, that may indicate that the pen arm backer is in the wrong position and that you need to move the whole pen arm closer to, or further from, the pen motor.
  
This is the result of the backer being inward too much, making the drawing curved to the right.
+
This pen arm backer shown above is in the correct position, since the pen tip points directly down and towards the thickest part of the egg, when the distal pen arm extends straight out and flat. For more on positioning the pen, see [http://wiki.evilmadscientist.com/Framing_and_Pen_Centering our notes on framing].
  
http://shop.emscdn.com/wiki/eggbot/quality/9B.jpg
 
  
http://shop.emscdn.com/wiki/eggbot/quality/10A-1.jpg
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/9B.jpg
  
this is when the backer os too far outward, causing the drawing to be curved to the left.
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/9A-1.jpg
  
http://shop.emscdn.com/wiki/eggbot/quality/10B.jpg
+
If the pen arm backer is too close to the pen motor, then you may see this kind of distortion-- curvature of the letters with respect to the pen motor position.
  
=== Pen arm not flat when in the down position===
 
http://shop.emscdn.com/wiki/eggbot/quality/16A.jpg
 
  
This occurs when the pen arm is not horizontal when in the down position, causing the pen to be skewed. The drawings can then come out slightly distorted. This is similar to when the backer is misaligned.
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/10B.jpg
  
===Bumping the pen arm===
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/10A-1.jpg
http://shop.emscdn.com/wiki/eggbot/quality/20A.jpg
 
  
This drawing is a test of what the outcome should be when everything goes correctly.
+
And similarly, when the pen arm backer is too far from the pen motor.
  
http://shop.emscdn.com/wiki/eggbot/quality/21A.jpg
 
  
This one is when the starting position of the pen arm was off and the pen arm bumped into the side of the EggBot. With the pen arm not being allowed to go any further, the EggBot continued the drawing at the position it was stuck at.
 
  
http://shop.emscdn.com/wiki/eggbot/quality/21B.jpg
+
----
  
===Distortion===
+
===Map Projection===
http://shop.emscdn.com/wiki/eggbot/quality/22A.jpg
 
  
This is an example of the distortion created when trying to draw a circle in a square on an egg and a spherical ornament.
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/24A.jpg
  
http://shop.emscdn.com/wiki/eggbot/quality/24A.jpg
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/22A.jpg
  
 +
These two plots show an example file -- a circle inside of a square -- that are plotted on a (roughly) spherical ornament and on an egg.  And yet, they don't really look like that-- and this isn't really an "error."  While some of the distortion that you see is due to minor misalignments within the EggBot, a more major factor to consider is the change in geometry that comes from projecting our rectangular drawing file onto a non-flat surface.  In geometry, this is called a [http://en.wikipedia.org/wiki/Map_projection map projection], and the EggBot uses [http://en.wikipedia.org/wiki/Equirectangular_projection equirectangular projection], where distances are mapped directly to angles. 
 +
 +
On the sphere, the circle appears (more or less) spherical.  The square's top and bottom are straight (when photographed from this particular angle), but the other two sides (longitude lines) do not appear straight (when photographed form this angle).  On the egg, the distortions are more severe because the curvature is so different in the two axes.  We usually compensate for this (when drawing on eggs) by stretching the design horizontally by about 150%.
 +
(See also [http://wiki.evilmadscientist.com/Eggbot_Troubleshooting#ellipses this note] from our troubleshooting guide.)
 +
 +
(You can download the circle and square example file [https://cdn.evilmadscientist.com/wiki/eggbot/quality/calexamples/CircleSquare.svg here].)
  
 
== "Software" issues ==
 
== "Software" issues ==
  
 
=== Motor reversal issues ===
 
=== Motor reversal issues ===
http://shop.emscdn.com/wiki/eggbot/quality/5A.jpg
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/5A.jpg
 +
 
 +
Doh! This occurred when the "Reverse motion of Motor 1 (pen)" was left unchecked when the egg was positioned so that its "fat" end was on the headstock. This can also happen when the "Reverse motion of Motor 1 (pen)" is checked, but the eggs "fat" end is in the tailstock.
  
This occurred when the "Reverse motion of Motor 1 (pen)" was left unchecked when the egg was positioned so that its "fat" end was on the headstock. This can also happen when the "Reverse motion of Motor 1 (pen)" is checked, but the eggs "fat" end is in the tailstock.
 
  
http://shop.emscdn.com/wiki/eggbot/quality/6A.jpg
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/6A.jpg
  
This mirrored image of "Hello World" is the result of "Reverse motion of Motor 2 (egg)" being left unchecked while the "fat" end of the egg is in the headstock, and vice versa.
+
This [http://wiki.evilmadscientist.com/Eggbot_Troubleshooting#mirrored mirrored image] of "Hello World" is the result of "Reverse motion of Motor 2 (egg)" being left unchecked while the "fat" end of the egg is in the headstock, and vice versa. If you leave both "reverse motion" setting unchecked, then you will get an [http://wiki.evilmadscientist.com/Eggbot_Troubleshooting#upsidedown upside down image].
 +
 
 +
 
 +
 
 +
----
  
 
=== Timing issues ===
 
=== Timing issues ===
http://shop.emscdn.com/wiki/eggbot/quality/4A.jpg
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/4A.jpg
 +
 
 +
This is the result of moving too fast.  The "Speed when pen is down" setting was set to 700 steps/s, which is usually too fast to create a neat drawing. The speed of the motor caused the pen to shake when drawing.
 +
 
 +
 
 +
https://cdn.evilmadscientist.com/wiki/eggbot/quality/2A.jpg
  
This is the result of the "Speed when pen is down" setting being set to 700 steps/s, which is too fast to create a neat drawing. The speed of the motor caused the lines to be jagged.
+
With the "Speed when the pen is down" setting set to 500 steps/s, while it is an improvement, the pen is still shaking.
  
http://shop.emscdn.com/wiki/eggbot/quality/2A.jpg
 
  
With the "Speed when the pen is down" setting set to 500 steps/s, while it is an improvement, is still too fast. There are still jagged lines.
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/7A.jpg
  
http://shop.emscdn.com/wiki/eggbot/quality/7A.jpg
+
This can happen when the "Delay after lowering pen" setting is set too low. The EggBot will start to commence the drawing before the pen has actually made contact with the egg, leaving gaps in your drawings.
  
This happens when the "Delay after lowering pen" setting is set too low. The EggBot will start to commence the drawing before the pen has actually made contact with the egg, leaving gaps in your drawings.
 
  
http://shop.emscdn.com/wiki/eggbot/quality/8A.jpg
+
https://cdn.evilmadscientist.com/wiki/eggbot/quality/8A.jpg
  
 
This is when the "Delay after raising pen" setting is set too low. The EggBot will start to move to the next destination before the pen is lifted off of the egg, leaving stray marks.
 
This is when the "Delay after raising pen" setting is set too low. The EggBot will start to move to the next destination before the pen is lifted off of the egg, leaving stray marks.
 +
 +
 +
 +
== Additional resources ==
 +
 +
For more about improving the results that you're getting with the EggBot, please see these additional pages on our wiki:
 +
 +
* [[Framing_and_Pen_Centering|Framing and Pen Centering]]
 +
* [[The_Eggbot_coordinate_system|The EggBot Coordinate System]]
 +
* [[Improving_precision|Improving precision]]

Latest revision as of 08:32, 13 March 2020

This wiki page is part of the documentation for The Original Egg-Bot.
Click here to return to the Egg-Bot overview.

If you are having quality issues with your prints that might be due to a misalignment of some sort, we hope that this guide will help you to find the source of the problem. This guide contains some helpful pictures that show how configuring the EggBot in different ways can produce different outcomes.


"Hardware" issues[edit]

Our test file[edit]

1A.jpg

This is the test file that we'll be using for most of the examples. Note that the print quality is fine and consistent. The "O's" have closed shapes, the vertical parts are vertical, the horizontal parts are horizontal, the slants of the "W's" have consistent width, and so forth. (Some of the examples that we'll show later do not have these properties!) Additionally, one should be able to print an example like this several times over itself without seeing any variation except that the lines appear darker after each successive pass.

You can download the example file here.

This was printed with the Deluxe EggBot on a chicken egg with an Ultra Fine Point Sharpie. The egg was oriented with its "fat" side (the side pointing down in the photo above) pointing towards the egg motor (headstock).

The print settings were as follows:

  • Timing tab:
    • Speed when pen is down: 300 steps/s
    • Speed when pen is up: 400 steps/s
    • Pen raising speed: 50 %/s
    • Delay after raising pen: 200 ms
    • Pen lowering speed: 20 %/s
    • Delay after lowering pen: 400 ms
  • Options tab:
    • Reverse motion of Motor 1 (pen): checked
    • Reverse motion of Motor 2 (egg): checked
    • Egg (x) axis wraps around: checked
    • Return home when done: checked
    • Enable engraver, if attached: unchecked
    • Curve smoothing (lower for more): 0.2



Dry pen[edit]

3A.jpg

A common problem that can happen when using old pens, or pens that have been left uncapped is that the pen does not start drawing immediately when you expect it to. It is usually easy to fix this problem by taking a scratch piece of paper and, right before you start your EggBot, "bleeding" your pen a little on the paper to get the ink flowing again, as shown below. Sharpie pens last approximately forever if treated well; if it doesn't start drawing immediately, you might consider leaving it capped for a few days and trying again, rather than throwing it out. You might also consider wetting the tip with solvent to reconnect the tip to the ink reservoir in the pen. For example, with a Sharpie you would make a small puddle of Isopropyl (rubbing) alcohol on a piece of paper. Then you would dip the dried-out tip in the puddle, and then try scribbling on the paper to see if ink flow begins.


1F-2.jpg



Alignment of the egg in the egg cups[edit]

15A.jpg

This skewed image is the result of misaligning the egg within the couplers, like so (exaggerated for clarity):

15B.jpg


In order to avoid this you should place the egg between the couplers with the egg as flush as you can get it against each coupler. To align the egg in place, turn the egg (or the egg coupler) and watch the egg as you turn it. (You may want to use the "Raise pen, turn off motors" option in EggBot Control to make this easy.) Adjust its position until there is as little wobbling as possible; that is, until it doesn't seem to "change shape" as you rotate it.


1E.jpg

This egg is properly aligned.



Loose Eggs & Screws[edit]

17A.jpg

If your plots look like this, with circles that don't close and differing widths of your letter parts, it likely means that something is loose. It can be either the egg itself-- slipping in the coupler -- or a loose screw somewhere on the EggBot. Make sure that the egg has a secure connection to the motor through its coupler, and can't wiggle independently of the motor. And, make sure that the screws on the EggBot are tight and secure (you can also check our troubleshooting guide here).


17B.jpg

If the hex screw below the pen arm's hinge is loose, the pen arm will move left and right as the pen is dragged across the egg. Try to gently wiggle the pen arm left to right. With the exception of the normal flexing of the hinge, it should not move at all.


18A.jpg

In this case, the screw that mounts the distal pen arm assembly to the proximal pen arm (shown below) was loose, with the kind of poor results that you might expect.

18B.jpg

19A.jpg

The plot above-- where the pen is wandering "all over the place" was caused by trying to draw when the screw that holds the pen was loose (about to drop the pen).

19B.jpg

To check if the pen is securely fastened, gently try to pull it out.



Pen arm bumps against frame[edit]

20A.jpg

Here is the "diamond" test pattern, shown without any major quality issues (for reference). (You can download the example file here.)


21B.jpg

21A.jpg

Here is the same pattern, but drawn with the EggBot misaligned such that the starting position of the pen arm was poor and the pen arm bumped into the tailstock of the EggBot while drawing. When the pen arm reaches the end of its range, it may bend and try to continue plotting there, or the motor may skip a step ("cog") and lose alignment.

If you are having trouble with hitting the sides, check before plotting -- using the manual ("walk motor") commands if necessary -- to make sure that the pen arm has free travel over the entire range that you intend to use. For more information about positioning the pen arm, see here.

If the pen moves but seems to just "fall over" without any resistance, you may still need to adjust your motor current.



Vertical position of the pen motor[edit]

1C-3.jpg

The pen motor can be moved vertically to adjust the pen arm for drawing on spherical or ellipsoidal surfaces. For drawing on chicken eggs, we normally position the pen motor about in the middle of the slots as shown here. For a sphere, position the motor at the very top of its slots. For a more elongated egg (maybe a turkey egg?) you may need to go lower yet in the slots.


11A.1.jpg

If the pen motor is positioned too high in the vertical slots (here, at the top of its slots while printing on a chicken egg), the pen will not make contact over the full surface. To correct this, lower the motor in the slots.


12B.jpg

12A.1.jpg

Conversely, if the pen motor is too low in its slots, the pen may not make contact at the edges of the plot region.

11B.jpg




Headstock / Tailstock position[edit]

1D-3.jpg

When the headstock is correctly positioned, the shaft of the pen motor points directly toward the thickest part of the egg (or sphere), as shown above.


13B.jpg

14A.1.jpg

When the headstock and tailstock are misplaced such that the pen motor is positioned too far to one side, you will find that (1) the pen cannot reach the surface everywhere that you would expect it to and (2) there will be some distortion of the print due to the misalignment. For more on positioning the motor see here.


14B.jpg

13A.1.jpg

A similar condition, in the opposite direction.



Horizontal position of the pen arm[edit]

1G.jpg

This photo shows the correct orientation for the distal pen arm and pen. Note that when the tip of the pen contacts the egg, the distal pen arm extends out straight and flat, down towards the center of the egg.


16B.jpg

16A.jpg

If, on the other hand, the pen arm is not horizontal when in the down position, it will cause the drawing to be skewed. (You will see similar types of issues when the pen arm backer is in the wrong position.)



Pen arm backer position[edit]

1B.jpg

When the distal pen arm is correctly positioned-- dead flat when it the pen tip is contacting the egg -- then the tip of the pen should point directly down and towards the thickest part of the egg. If it does not, that may indicate that the pen arm backer is in the wrong position and that you need to move the whole pen arm closer to, or further from, the pen motor.

This pen arm backer shown above is in the correct position, since the pen tip points directly down and towards the thickest part of the egg, when the distal pen arm extends straight out and flat. For more on positioning the pen, see our notes on framing.


9B.jpg

9A-1.jpg

If the pen arm backer is too close to the pen motor, then you may see this kind of distortion-- curvature of the letters with respect to the pen motor position.


10B.jpg

10A-1.jpg

And similarly, when the pen arm backer is too far from the pen motor.



Map Projection[edit]

24A.jpg

22A.jpg

These two plots show an example file -- a circle inside of a square -- that are plotted on a (roughly) spherical ornament and on an egg. And yet, they don't really look like that-- and this isn't really an "error." While some of the distortion that you see is due to minor misalignments within the EggBot, a more major factor to consider is the change in geometry that comes from projecting our rectangular drawing file onto a non-flat surface. In geometry, this is called a map projection, and the EggBot uses equirectangular projection, where distances are mapped directly to angles.

On the sphere, the circle appears (more or less) spherical. The square's top and bottom are straight (when photographed from this particular angle), but the other two sides (longitude lines) do not appear straight (when photographed form this angle). On the egg, the distortions are more severe because the curvature is so different in the two axes. We usually compensate for this (when drawing on eggs) by stretching the design horizontally by about 150%. (See also this note from our troubleshooting guide.)

(You can download the circle and square example file here.)

"Software" issues[edit]

Motor reversal issues[edit]

5A.jpg

Doh! This occurred when the "Reverse motion of Motor 1 (pen)" was left unchecked when the egg was positioned so that its "fat" end was on the headstock. This can also happen when the "Reverse motion of Motor 1 (pen)" is checked, but the eggs "fat" end is in the tailstock.


6A.jpg

This mirrored image of "Hello World" is the result of "Reverse motion of Motor 2 (egg)" being left unchecked while the "fat" end of the egg is in the headstock, and vice versa. If you leave both "reverse motion" setting unchecked, then you will get an upside down image.



Timing issues[edit]

4A.jpg

This is the result of moving too fast. The "Speed when pen is down" setting was set to 700 steps/s, which is usually too fast to create a neat drawing. The speed of the motor caused the pen to shake when drawing.


2A.jpg

With the "Speed when the pen is down" setting set to 500 steps/s, while it is an improvement, the pen is still shaking.


7A.jpg

This can happen when the "Delay after lowering pen" setting is set too low. The EggBot will start to commence the drawing before the pen has actually made contact with the egg, leaving gaps in your drawings.


8A.jpg

This is when the "Delay after raising pen" setting is set too low. The EggBot will start to move to the next destination before the pen is lifted off of the egg, leaving stray marks.


Additional resources[edit]

For more about improving the results that you're getting with the EggBot, please see these additional pages on our wiki: