Editing ISP Shield 2 Assembly Instructions

Jump to: navigation, search

Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision Your text
Line 2: Line 2:
  
 
== Bill of Materials, or, "What's in the kit?" ==
 
== Bill of Materials, or, "What's in the kit?" ==
{| cellpadding="3" {{table}}
+
 
| align="center" style="background:#f0f0f0;"|''' Line '''
+
{| border="1" cellspacing="0" cellpadding="4" |
| align="center" style="background:#f0f0f0;"|''' Qty '''
+
|Line
| align="center" style="background:#f0f0f0;"|''' Reference '''
+
|Ref Des
| align="center" style="background:#f0f0f0;"|''' Value '''
+
|Description
| align="center" style="background:#f0f0f0;"|''' Vendor '''
+
|Type
| align="center" style="background:#f0f0f0;"|''' Vendor Part# '''
+
|Vendor
|-
+
|Vendor Part Number
 +
|Quantity
 +
|----
 
|1
 
|1
 +
| n/a
 +
|PCB for ISP Shield 2.0
 +
|Printed circuit board
 +
|Evil Mad Science
 +
|[http://evilmadscience.com/productsmenu/tinykitlist/254 681]
 
|1
 
|1
|n/a
+
|----
|Printed circuit board for ISP Shield 2.0
 
|Evil Mad Scientist
 
|[http://shop.evilmadscientist.com/productsmenu/tinykitlist/254 9600026]
 
|-
 
 
|2
 
|2
|1
 
 
|R1
 
|R1
|Reset line pull-up resistor, 10k, 1/6 W
+
|Reset line pull-up resistor
 +
|10k, 1/6 W
 
|Digikey
 
|Digikey
|10KETR-ND
+
|[http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=10KETR-ND 10KETR-ND]
|-
+
|1
 +
|----
 
|3
 
|3
|5
 
 
|R2 thru R6
 
|R2 thru R6
|Reset and LED load resistors, 1000 ohm, 1/4 W
+
|Reset and LED load resistors
 +
|1000 ohm, 1/4 W
 
|Digikey
 
|Digikey
|1.0KQBK-ND
+
|[http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=1.0KQBK-ND 1.0KQBK-ND]
|-
+
|5
 +
|----
 
|4
 
|4
|1
 
 
|R7
 
|R7
|Auto-reset overrride resistor, 100 ohm, 1/4 W
+
|Auto-reset overrride resistor
 +
|100 ohm, 1/4 W
 
|Digikey
 
|Digikey
|100QBK-ND
+
|[http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=100QBK-ND 100QBK-ND]
|-
+
|1
 +
|----
 
|5
 
|5
 +
|J5, J6
 +
|Target Power Enable, Auto-Reset Overrride (Header)
 +
|6 pin right-angle header, 0.1” spacing
 +
|Digikey
 +
|[http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=SAM1043-06-ND SAM1043-06-ND]
 
|1
 
|1
|J5, J6
+
|----
|Target Power Enable, Auto-Reset Overrride; 6 pin right-angle header
 
|Evil Mad Scientist
 
|[http://shop.evilmadscientist.com/productsmenu/partsmenu/292 9200007]
 
|-
 
 
|6
 
|6
 +
|PROG, ERROR, PULSE, HELLO
 +
|Indicator LED
 +
|3mm, Diffused Yellow
 +
|Evil Mad Science
 +
|[http://evilmadscience.com/productsmenu/partsmenu/89-led#3mmdiff 357]
 
|4
 
|4
|PROG,ERROR,PULSE,HELLO
+
|----
|Indicator LED, 3mm, Diffused Yellow
 
|Evil Mad Scientist
 
|[http://shop.evilmadscientist.com/productsmenu/partsmenu/339 9330030]
 
|-
 
 
|7
 
|7
8
+
|XTL
 +
|Crystal
 +
|16 MHz
 +
|Digikey
 +
|[http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=XC1721-ND XC1721-ND]
 
|1
 
|1
2
+
|----
|XTL
+
|8
C2, C3
+
|C2, C3
|Crystal, 16 mHz
+
|Capacitors for crystal
Capacitors for crystal, 18pF, 50 V ceramic
+
|18pF, 50 V ceramic
|Evil Mad Scientist
+
|Digikey
|[http://shop.evilmadscientist.com/productsmenu/partsmenu/144-xtlcaps 630]
+
|[http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=BC1004CT-ND BC1004CT-ND]
|-
+
|2
 +
|----
 
|9
 
|9
|2
 
 
|C1
 
|C1
|Bypass Capacitor, 0.1uF
+
|Bypass Capacitor
 +
|0.1uF Capacitor
 
|Digikey
 
|Digikey
|BC1148TR-ND
+
|[http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=BC1148CT-ND BC1148TR-ND]
|-
+
|2
 +
|----
 
|10
 
|10
 +
|S1
 +
|Reset Switch
 +
|Tactile pushbutton switch
 +
|Digikey
 +
|[http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=679-2452-ND 679-2452-ND]
 
|1
 
|1
|S1
+
|----
|Tactile pushbutton reset switch
 
|Evil Mad Scientist
 
|[http://shop.evilmadscientist.com/productsmenu/partsmenu/520 9430004]
 
|-
 
 
|11
 
|11
 +
|ISP6
 +
|6 pin ISP Header
 +
|2x3 pin 0.1” spaced DIL header
 +
|Digikey
 +
|[http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=609-3202-ND 609-3202-ND]
 
|1
 
|1
|ISP6
+
|----
|ISP Header, 2x3 pin 0.1” spaced DIL
 
|Evil Mad Scientist
 
|[http://shop.evilmadscientist.com/productsmenu/partsmenu/143 9200005]
 
|-
 
 
|12
 
|12
 +
|J1 thru J4
 +
|Header set, 6-pin (2 pcs), 8-pin (2 pcs)
 +
|Stacking type  header, 0.1” spacing
 +
|Evil Mad Science
 +
|[http://evilmadscience.com/productsmenu/partsmenu/251 633]
 
|1
 
|1
|J1 thru J4
+
|----
|Stacking Header set, 6-pin (2 pcs), 8-pin (2 pcs) 0.1” spacing
 
|Evil Mad Scientist
 
|[http://shop.evilmadscientist.com/productsmenu/partsmenu/251 633]
 
|-
 
 
|13
 
|13
 +
|U1
 +
|ZIF DIP Socket
 +
|28 pin, 0.3" pin spacing
 +
|Evil Mad Science
 +
|[http://evilmadscience.com/productsmenu/partsmenu/54-zif20 212]
 
|1
 
|1
|U1
+
|----
|28 pin ZIF DIP Socket
 
|Evil Mad Scientist
 
|[http://shop.evilmadscientist.com/productsmenu/partsmenu/54 9220005]
 
|-
 
 
|14
 
|14
 +
|J5, J6 (jumper)
 +
|Target Power Enable, Auto-Reset Override (Jumper)
 +
|2 pin jumper block, 0.1” spacing
 +
|Digikey
 +
|[http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=A26242-ND A26242-ND]
 
|2
 
|2
|J5, J6 (jumper)
+
|----
|Target Power Enable, Auto-Reset Override, 2 pin Jumper
 
|Evil Mad Scientist
 
|[http://shop.evilmadscientist.com/productsmenu/partsmenu/288 9200001]
 
|-
 
 
|}
 
|}
  
Line 165: Line 184:
 
First, carefully solder just one pin to the board as shown above. (We suggest the one with the square pad.)  Then, make sure the long pins on the header are parallel with the board and that the header is fully seated on the board: the black plastic block should be flush to the board.  If this is not the case, carefully reheat the soldered joint and adjust the header as needed.  Be careful-- it will be hot!
 
First, carefully solder just one pin to the board as shown above. (We suggest the one with the square pad.)  Then, make sure the long pins on the header are parallel with the board and that the header is fully seated on the board: the black plastic block should be flush to the board.  If this is not the case, carefully reheat the soldered joint and adjust the header as needed.  Be careful-- it will be hot!
  
A second option is to slide the 2-pin jumpers onto the long pins in order to maintain the proper gap between the board and pins when you flip the board over.  We suggest you slide it onto pins 1 and 2 and the other onto 5 and 6; then solder pin 3 and 4 to hold it in place.  Before soldering the remaining pins remove the jumpers to avoid any damage that could be caused by heating the pins during soldering.
+
 
  
 
http://shop.emscdn.com/wiki/ispshield/assy_v2/09.jpg
 
http://shop.emscdn.com/wiki/ispshield/assy_v2/09.jpg
Line 175: Line 194:
  
 
http://shop.emscdn.com/wiki/ispshield/assy_v2/10.jpg
 
http://shop.emscdn.com/wiki/ispshield/assy_v2/10.jpg
 +
 +
  
 
=== 4. The LEDs ===  
 
=== 4. The LEDs ===  
Line 188: Line 209:
 
http://shop.emscdn.com/wiki/ispshield/assy_v2/14.jpg
 
http://shop.emscdn.com/wiki/ispshield/assy_v2/14.jpg
  
 +
If everything is correct, the flat faces of each LED will appear as shown above.
  
  
Line 214: Line 236:
 
=== 7.  0.1 uF ceramic capacitor ===
 
=== 7.  0.1 uF ceramic capacitor ===
  
There are two in the kit. One goes in location C1.  It looks just like the 18 pF capacitor, but without the black stripe.  It is not directional; it can go in either way.  Solder it in place and clip the leads. [The assumption is that that the "other" 0.1uF ceramic capacitor is a gift and can be used as you wish, but isn't needed for this project.]
+
There are two in the kit. One goes in location C1.  It looks just like the 18 pF capacitor, but without the black stripe.  It is not directional; it can go in either way.  Solder it in place and clip the leads.
  
 
=== 8.  Reset switch ===
 
=== 8.  Reset switch ===

Please note that all contributions to Evil Mad Scientist Wiki are considered to be released under the GNU Free Documentation License 1.3 (see Evil Mad Scientist Wiki:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To edit this page, please answer the question that appears below (more info):

Cancel | Editing help (opens in new window)

Template used on this page: