Editing Simple Relay Shield Assembly v2

Jump to: navigation, search

Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision Your text
Line 60: Line 60:
 
First, bend the resistor leads as shown:
 
First, bend the resistor leads as shown:
  
http://shop.emscdn.com/wiki/relayshield/assy_v2/4a.jpg
+
http://shop.emscdn.com/wiki/relayshield/assy_v1/4.jpg
  
  
Line 66: Line 66:
 
Insert the first resistor in location R1 (Resistors are not directional and can be installed either way):
 
Insert the first resistor in location R1 (Resistors are not directional and can be installed either way):
  
http://shop.emscdn.com/wiki/relayshield/assy_v2/5.jpg
+
http://shop.emscdn.com/wiki/relayshield/assy_v1/5.jpg
  
  
Line 72: Line 72:
 
Bend the leads outward to keep the resistor in place while soldering:
 
Bend the leads outward to keep the resistor in place while soldering:
  
http://shop.emscdn.com/wiki/relayshield/assy_v2/6.jpg
+
http://shop.emscdn.com/wiki/relayshield/assy_v1/6.jpg
  
  
Line 78: Line 78:
 
Solder both leads:
 
Solder both leads:
  
http://shop.emscdn.com/wiki/relayshield/assy_v2/7.jpg
+
http://shop.emscdn.com/wiki/relayshield/assy_v1/7.jpg
  
  
Line 84: Line 84:
 
Make sure you have a good solder joint from the PCB pad to the resistor lead. The solder joint should be shiny without too much excess solder.
 
Make sure you have a good solder joint from the PCB pad to the resistor lead. The solder joint should be shiny without too much excess solder.
  
http://shop.emscdn.com/wiki/relayshield/assy_v2/8.jpg
+
http://shop.emscdn.com/wiki/relayshield/assy_v1/9.jpg
  
  
Line 90: Line 90:
 
Clip the excess leads short on the back side.  
 
Clip the excess leads short on the back side.  
  
http://shop.emscdn.com/wiki/relayshield/assy_v2/9.jpg
+
http://shop.emscdn.com/wiki/relayshield/assy_v1/10.jpg
  
http://shop.emscdn.com/wiki/relayshield/assy_v2/10.jpg
+
http://shop.emscdn.com/wiki/relayshield/assy_v1/11.jpg
  
 
Then, install the second 1k ohm resistor at location R2, in the same manner.  Again, solder both pins and clip the excess leads short.
 
Then, install the second 1k ohm resistor at location R2, in the same manner.  Again, solder both pins and clip the excess leads short.
Line 99: Line 99:
 
When you've finished adding these two resistors, your board should look like this:
 
When you've finished adding these two resistors, your board should look like this:
  
http://shop.emscdn.com/wiki/relayshield/assy_v2/12.jpg
+
http://shop.emscdn.com/wiki/relayshield/assy_v1/12.jpg
  
 
=== 2. Install the two diodes ===
 
=== 2. Install the two diodes ===

Please note that all contributions to Evil Mad Scientist Wiki are considered to be released under the GNU Free Documentation License 1.3 (see Evil Mad Scientist Wiki:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To edit this page, please answer the question that appears below (more info):

Cancel | Editing help (opens in new window)

Template used on this page: