Difference between revisions of "Using The ISP Shield 2"

From Evil Mad Scientist Wiki
Jump to: navigation, search
(...To use the ISP Shield 2.0 in place of an AVR ISP)
m (...To program the Arduino Bootloader onto an ATmega168/ATmega328)
Line 10: Line 10:
 
#Upload this sketch to your Arduino or Arduino clone
 
#Upload this sketch to your Arduino or Arduino clone
 
#At this time place an ATmega168 or ATmega328 into the ZIF socket on the ISP Shield 2.0 and lock it in place
 
#At this time place an ATmega168 or ATmega328 into the ZIF socket on the ISP Shield 2.0 and lock it in place
 +
#The lever of the ZIF socket corresponds to pin 1 on the Atmega328, which is opposite of the retail Arduino Uno Rev3
 
#In the '''Tools''' menu, select '''Board''', and select either:
 
#In the '''Tools''' menu, select '''Board''', and select either:
 
#* '''Arduino Duemilanove or Nano w/ ATmega328''' if you are programing an ATmega328
 
#* '''Arduino Duemilanove or Nano w/ ATmega328''' if you are programing an ATmega328
 
#* '''Arduino Diecimila, Duemilanove, or Nano w/ ATmega168''' if you are programing an ATmega168
 
#* '''Arduino Diecimila, Duemilanove, or Nano w/ ATmega168''' if you are programing an ATmega168
 +
#Be sure to have J5 jumpered to YUP and J6 jumpered to NO WAY
 
#In the '''Tools''' menu, select '''Burn Bootloader''', and select '''w/ Arduino as ISP'''
 
#In the '''Tools''' menu, select '''Burn Bootloader''', and select '''w/ Arduino as ISP'''
  

Revision as of 19:07, 29 September 2013

This page covers basic usage of the Evil Mad Science ISP Shield 2.0


...To program the Arduino Bootloader onto an ATmega168/ATmega328

  1. Attach the ISP Shield 2.0 to the Arduino. If using Arduino Uno, put a piece of insulating tape on top of the USB connector of the Uno to prevent the bottom of the shield from shorting against the connector housing. (Or, use a Googly Shield!)
  2. Connect the Arduino to your computer and bring up the Arduino IDE
  3. If necessary, configure the Arduino IDE for your Arduino or Arduino clone
  4. In the File menu, select Examples, and open the ArduinoISP sketch
  5. Upload this sketch to your Arduino or Arduino clone
  6. At this time place an ATmega168 or ATmega328 into the ZIF socket on the ISP Shield 2.0 and lock it in place
  7. The lever of the ZIF socket corresponds to pin 1 on the Atmega328, which is opposite of the retail Arduino Uno Rev3
  8. In the Tools menu, select Board, and select either:
    • Arduino Duemilanove or Nano w/ ATmega328 if you are programing an ATmega328
    • Arduino Diecimila, Duemilanove, or Nano w/ ATmega168 if you are programing an ATmega168
  9. Be sure to have J5 jumpered to YUP and J6 jumpered to NO WAY
  10. In the Tools menu, select Burn Bootloader, and select w/ Arduino as ISP

...To program the Arduino Bootloader onto an ATmega168/ATmega328 located on an external target board

You can also use the ISP Shield 2.0 to program the Arduino bootloader onto an external target board, providing that the target is Arduino compatible and has a standard 6-pin* AVR ISP programming header.

Follow the instructions above, however instead of placing a microcontroller into the ZIF socket connect the ISP Shield 2.0 to the target board with a 6 pin (2x3 DIL) ribbon cable. Be sure to get the orientation correct; pin 1 is marked with an arrow on the ISP Shield 2.0 circuit board.

In addition, make sure that the target power jumper is set correctly on the ISP Shield 2.0. If your target board has its own power, the jumper (location J5) should be set to 'Nope', like so:

27.jpg

It is important to make sure that your target is genuinely Arduino compatible, and that you select the appropriate target board type from the Arduino Tools menu. If you are programming an ATmega168 your target board will need the appropriate crystal and related capacitors. If you are programming an ATmega328 your target board may have an appropriate crystal and related capacitors. However if you wish to use the internal oscillator instead you need to install support for an additional hardware configuration. Check the From Arduino to a Microcontroller on a Breadboard tutorial by the Arduino Team - under the Minimal Circuit (Eliminating the External Clock) section there are instructions for downloading and installing the ATmega328 on a breadboard (8 MHz internal clock) hardware configuration in the Arduino IDE. Once installed, select this Board type when programming an ATmega328 on an external target board that has no crystal.


...To use the ISP Shield 2.0 in place of an AVR ISP

The ArduinoISP sketch mimics the Atmel AVRISP programmer. You can use use avrdude to upload compiled programs to an ATmega168/ATmega328 via the ISP Shield 2.0 ZIF socket or either of the ISP headers. With the Arduino IDE, you can upload sketches with the ISP Shield by pressing and holding the shift key before clicking the Upload icon. Normally when you hover the mouse over the icon you will see "Upload". When holding the shift key it will show "Upload Using Programmer."

When using an Arduino and ArduinoISP in this capacity the avrdude programmer type should be set to 'avrisp'. If you are using Windows avrdude may not be able to use the Arduino unless it is attached to COM port 9 (COM9) or lower. To change the port number that a device is attached to first locate it in the Device Manager: in the System Properties control panel, select the Hardware tab, then click the Device Manager button, and finally expand the Ports (COM & LPT) item. Right click the appropriate device for your Arduino and select Properties option, select the Port Settings tab, and click the button labeled Advanced.... Select a new unused port in the COM Port Number drop-down selection box.

Check the avrdude webpage for complete instructions and documentation regarding the use of avrdude.

Known Issue With Auto-Reset

There is a known issue with auto-reset (a common feature on Arduino boards) and the ArduinoISP technique. You may, for example, get the "not in sync: resp=0x15" error message. If so, you may need to disable auto-reset. The ISP Shield 2.0 has a resistor on board for this eventuality.

Locate header J6 on the ISP Shield 2.0 and connect a jumper across the top and middle pins to override auto-reset, like so:

28.jpg

Connecting a jumper across the bottom two pins (or leaving the jumper off entirely) will allow the Arduino board to function normally:

29.jpg


Known Issue With Arduino Uno

We have found the ISP shield to work well when situated on top of the Arduino Uno, if you add a small capacitor, 0.1 uF or so, between RST and GND on the ISP shield. We recommend placing it into header J4, spanning from the leftmost pin (RST) to one of the two GND pins.

This is similar to the technique recommended in the ArduinoISP tutorial of putting a 10 uF capacitor there, but also editing the ArduinoISP to account for the longer time constant associated with the larger capacitor.