Editing Art Controller Assembly Instructions
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.
The edit can be undone.
Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision | Your text | ||
Line 1: | Line 1: | ||
− | |||
− | |||
== Assembly procedure == | == Assembly procedure == | ||
Line 8: | Line 6: | ||
− | === 0. The | + | === 0. The simple relay shield kit === |
Here are all the components that make up the kit: | Here are all the components that make up the kit: | ||
Line 15: | Line 13: | ||
− | + | We'll be adding components to the various locations labeled on the circuit board. | |
Line 52: | Line 50: | ||
− | The diodes will be installed in locations D1 and D2. Again bend the leads as shown: | + | The diodes will be installed in locations D1 and D2, as shown here: |
+ | |||
+ | http://shop.emscdn.com/wiki/artcontrol/18.jpg | ||
+ | |||
+ | |||
+ | http://shop.emscdn.com/wiki/artcontrol/19.jpg | ||
+ | |||
+ | |||
+ | Again bend the leads as shown: | ||
http://shop.emscdn.com/wiki/relayshield/assy_v1/15.jpg | http://shop.emscdn.com/wiki/relayshield/assy_v1/15.jpg | ||
Line 161: | Line 167: | ||
http://shop.emscdn.com/wiki/artcontrol/51.jpg | http://shop.emscdn.com/wiki/artcontrol/51.jpg | ||
− | Once you've bent the leads and inserted it, install the screw (item 10) and the kep nut-- a hex nut with integral lock washer, (item 11) --to hold the regulator in place. Tighten it well; the circuit board acts as a heat sink for the regulator, which can get very hot otherwise | + | Once you've bent the leads and inserted it, install the screw (item 10) and the kep nut-- a hex nut with integral lock washer, (item 11) --to hold the regulator in place. Tighten it well; the circuit board acts as a heat sink for the regulator, which can get very hot otherwise. Finally, solder the three pins and clip the excess leads. |
The photo above shows what the regulator looks like on the completed board, screwed down into place and soldered. | The photo above shows what the regulator looks like on the completed board, screwed down into place and soldered. | ||
Line 171: | Line 177: | ||
− | The | + | The programming header will be installed in J4, here: |
http://shop.emscdn.com/wiki/artcontrol/36b.jpg | http://shop.emscdn.com/wiki/artcontrol/36b.jpg | ||
− | + | To install this component, we recommend inserting the header and then resting the board-- upside down --on the header. Rather than soldering all 6 pins at once, first solder 'tack' one leg as shown below: | |
− | |||
− | |||
− | Rather than soldering all 6 pins at once, first solder 'tack' one leg as shown below: | ||
http://shop.emscdn.com/wiki/artcontrol/37.jpg | http://shop.emscdn.com/wiki/artcontrol/37.jpg | ||
− | + | Then, verify that the header sits flush to the board before soldering the other six pins. | |
− | |||
− | |||
Line 222: | Line 223: | ||
− | === 10. The terminal | + | === 10. The terminal block === |
http://shop.emscdn.com/wiki/artcontrol/43.jpg | http://shop.emscdn.com/wiki/artcontrol/43.jpg | ||
Line 281: | Line 282: | ||
http://shop.emscdn.com/wiki/artcontrol/53.jpg | http://shop.emscdn.com/wiki/artcontrol/53.jpg | ||
− | The final step is to insert the microcontroller into its socket | + | The final step is to insert the microcontroller into its socket. Orientation is critical: Make sure that the half-moon indentation at one end of the chip matches that on the socket and PCB. Insert it firmly, as far down into the socket as it will go. |