Editing ISP Shield Assembly Instructions
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.
The edit can be undone.
Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision | Your text | ||
Line 1: | Line 1: | ||
− | This page walks through the basic assembly process for building the [http://wiki.evilmadscience.com/ISP_Shield ISP Shield] | + | This page walks through the basic assembly process for building the [http://wiki.evilmadscience.com/ISP_Shield ISP Shield]. |
− | |||
− | |||
+ | http://evilmadscience.s3.amazonaws.com/catalog/emskits/ispshield/kit/imgmed/3.jpg | ||
Line 20: | Line 19: | ||
|PCB for ISP Shield | |PCB for ISP Shield | ||
|Printed circuit board | |Printed circuit board | ||
− | |Evil Mad | + | |Evil Mad Science |
− | |[http:// | + | |[http://evilmadscience.com/productsmenu/tinykitlist/254 681] |
|1 | |1 | ||
|---- | |---- | ||
Line 52: | Line 51: | ||
|Indicator LED | |Indicator LED | ||
|3mm, Diffused Yellow | |3mm, Diffused Yellow | ||
− | |Evil Mad | + | |Evil Mad Science |
− | |[http:// | + | |[http://evilmadscience.com/productsmenu/partsmenu/89-led#3mmdiff 357] |
|4 | |4 | ||
|---- | |---- | ||
Line 100: | Line 99: | ||
|Header set, 6-pin (2 pcs), 8-pin (2 pcs) | |Header set, 6-pin (2 pcs), 8-pin (2 pcs) | ||
|Stacking type header, 0.1” spacing | |Stacking type header, 0.1” spacing | ||
− | |Evil Mad | + | |Evil Mad Science |
− | |[http:// | + | |[http://evilmadscience.com/productsmenu/partsmenu/251 633] |
|1 | |1 | ||
|---- | |---- | ||
Line 108: | Line 107: | ||
|ZIF DIP Socket | |ZIF DIP Socket | ||
|28 pin, 0.3" pin spacing | |28 pin, 0.3" pin spacing | ||
− | |Evil Mad | + | |Evil Mad Science |
− | |[http:// | + | |[http://evilmadscience.com/productsmenu/partsmenu/54-zif20 212] |
|1 | |1 | ||
|---- | |---- | ||
Line 138: | Line 137: | ||
Here's what the bare circuit board looks like: | Here's what the bare circuit board looks like: | ||
− | http://evilmadscience.s3.amazonaws.com/ | + | http://evilmadscience.s3.amazonaws.com/catalog/emskits/ispshield/pcb/imgmed/1.jpg |
We'll be adding components to the labeled locations there. | We'll be adding components to the labeled locations there. | ||
Line 148: | Line 147: | ||
You can see the smaller size of the resistor in this photo: | You can see the smaller size of the resistor in this photo: | ||
− | + | ||
− | http://evilmadscience.s3.amazonaws.com/ | + | http://evilmadscience.s3.amazonaws.com/catalog/emskits/ispshield/kit/imgmed/1.jpg |
Line 202: | Line 201: | ||
These go in locations J1 through J4, and go straight through the board to provide connections to the Arduino board below. | These go in locations J1 through J4, and go straight through the board to provide connections to the Arduino board below. | ||
− | http://evilmadscience.s3.amazonaws.com/ | + | http://evilmadscience.s3.amazonaws.com/catalog/emskits/ispshield/kit/imgmed/2.jpg |
− | |||
To add these, we recommend inserting all four headers and then resting the board-- upside down --on the four headers, so that they sit flush to the board. Solder one end pin of each first. Then, flip it back over and make sure that all four pins are straight and flush to the board. This is important for good connections. Then, flip it upside down again and solder the rest of the pins. Try to avoid excess solder, so that solder does not wick either down into the hole (bad!) or onto the pins (also bad!). | To add these, we recommend inserting all four headers and then resting the board-- upside down --on the four headers, so that they sit flush to the board. Solder one end pin of each first. Then, flip it back over and make sure that all four pins are straight and flush to the board. This is important for good connections. Then, flip it upside down again and solder the rest of the pins. Try to avoid excess solder, so that solder does not wick either down into the hole (bad!) or onto the pins (also bad!). | ||
Line 222: | Line 220: | ||
− | === 13. Target power jumper === | + | === 13. Target power jumper === |
− | + | ||
− | http://evilmadscience.s3.amazonaws.com/ | + | http://evilmadscience.s3.amazonaws.com/catalog/emskits/ispshield/kit/imgmed/7.jpg http://evilmadscience.s3.amazonaws.com/catalog/emskits/ispshield/kit/imgmed/8.jpg |
If you are going to use your ISP Shield to program chips that are not in the ZIF socket, you'll need to add a 6-pin ribbon cable to connect to an appropriate external target. The ISP shield can, optionally provide 5 V power to your target. If you want to do this, slide the jumper over the two pins labeled "Yup." If not, keep it in the "Nope" position. | If you are going to use your ISP Shield to program chips that are not in the ZIF socket, you'll need to add a 6-pin ribbon cable to connect to an appropriate external target. The ISP shield can, optionally provide 5 V power to your target. If you want to do this, slide the jumper over the two pins labeled "Yup." If not, keep it in the "Nope" position. | ||
Line 234: | Line 232: | ||
http://evilmadscience.s3.amazonaws.com/wiki/ispshield/assy/imgmed/6.jpg | http://evilmadscience.s3.amazonaws.com/wiki/ispshield/assy/imgmed/6.jpg | ||
− | |||
− | |||
− | |||
Connect the resistor between the reset pin (far left on the lower header) and 5 V, two pins over. | Connect the resistor between the reset pin (far left on the lower header) and 5 V, two pins over. | ||
Alternately, if you have a Diavolino, you can disable auto-reset by clipping (or just not installing) the 0.1 uF capacitor in the upper left of the board, by the word "green." | Alternately, if you have a Diavolino, you can disable auto-reset by clipping (or just not installing) the 0.1 uF capacitor in the upper left of the board, by the word "green." |