Editing AYAB KH-910
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.
The edit can be undone.
Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision | Your text | ||
Line 36: | Line 36: | ||
<img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/910-closed@2x.jpg" width="800" height="222" > | <img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/910-closed@2x.jpg" width="800" height="222" > | ||
− | This is the Brother KH- | + | This is the Brother KH-900 knitting machine. Remove the screws on top of the machine that hold the top cover in place. The top cover comes in three sections, and all three will have to be loosened (or removed) in order to remove the leftmost section that we care about. |
Line 55: | Line 55: | ||
<img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/910-cover4@2x.jpg" width="800" height="427" > | <img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/910-cover4@2x.jpg" width="800" height="427" > | ||
− | Then (only after pushing it to the right) | + | Then (only after pushing it to the right) tilt it up and out of place to remove it. |
<img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/910-disconnect@2x.jpg" width="800" height="425" > | <img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/910-disconnect@2x.jpg" width="800" height="425" > | ||
− | Disconnect all of the cables that connect the circuit board inside this cover to the rest of the machine. | + | Disconnect all of the cables that connect the circuit board inside this cover to the rest of the machine. These connectors have locking clip "wings" on their edges. You will have to squeeze the clips as shown above to disconnect them. |
− | |||
− | |||
Line 70: | Line 68: | ||
− | <img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/910-rhs- | + | <img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/910-rhs-1@2x.jpg" width="800" height="533" > |
− | <img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/910-rhs- | + | <img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/910-rhs-2@2x.jpg" width="800" height="533" > |
Now, let's attach the first connector to the new AYAB interface. Hold the board as shown here, such that the majority of the exposed connectors are on the right, and identify the cable with the "S-2" label. Attach that cable to the "S-2" connector on the AYAB interface, with the labeled side of the cable connector (the label that says "S-2") facing towards the "S-2" label on the board. (The orientation of the connectors does matter.) | Now, let's attach the first connector to the new AYAB interface. Hold the board as shown here, such that the majority of the exposed connectors are on the right, and identify the cable with the "S-2" label. Attach that cable to the "S-2" connector on the AYAB interface, with the labeled side of the cable connector (the label that says "S-2") facing towards the "S-2" label on the board. (The orientation of the connectors does matter.) | ||
Line 79: | Line 77: | ||
− | <img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/ | + | <img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/900-lhs1@2x.jpg" width="800" height="408" > |
− | Next, add the other connectors. Start | + | Next, add the other connectors. Start by adding the largest connector on the left hand side of the board and work towards the smallest. There are four connectors, each with a differently-side plug. |
− | <img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/ | + | <img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/900-complete@2x.jpg" width="800" height="243" > |
Here is how the board should look once all of the connectors have been added. | Here is how the board should look once all of the connectors have been added. | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
Line 110: | Line 101: | ||
− | An important note is that the AYAB interface completely replaces the original power supply. Whether or not the original power supply on your machine worked, do not separately plug it into power while using the AYAB Interface, or indeed, any time that the cover is open. | + | An important note is that the AYAB interface completely replaces the original power supply. Whether or not the original power supply on your machine worked, do not separately plug it into power while using the AYAB Interface, or indeed, any time that the cover is open. |