Difference between revisions of "ISP Shield Assembly Instructions"
From Evil Mad Scientist Wiki
| Line 8: | Line 8: | ||
|Vendor | |Vendor | ||
|Vendor Part Number | |Vendor Part Number | ||
| − | |Quantity | + | |Quantity |
|---- | |---- | ||
|1 | |1 | ||
|J1 thru J4 | |J1 thru J4 | ||
| − | | | + | |Header set, 6-pin (2 pcs), 8-pin (2 pcs) |
| − | | | + | |Stacking type header, 0.1” spacing |
|Evil Mad Science | |Evil Mad Science | ||
|633 | |633 | ||
| Line 21: | Line 21: | ||
|J5 | |J5 | ||
|Target Power Enable, Header | |Target Power Enable, Header | ||
| − | |3 pin | + | |3 pin right-angle header, 0.1” spacing |
|Digikey | |Digikey | ||
|TSW-103-25-F-SRA-ND | |TSW-103-25-F-SRA-ND | ||
| Line 27: | Line 27: | ||
|---- | |---- | ||
|3 | |3 | ||
| − | | | + | |J5 (header) |
|Target Power Enable, Jumper | |Target Power Enable, Jumper | ||
| − | |2 pin jumper block | + | |2 pin jumper block, 0.1” spacing |
|Digikey | |Digikey | ||
|A26242-ND | |A26242-ND | ||
| Line 52: | Line 52: | ||
|6 | |6 | ||
|R1 | |R1 | ||
| − | |Reset | + | |Reset line pull-up resistor |
| − | | | + | |10k, 1/6 W |
|Digikey | |Digikey | ||
|10KETR-ND | |10KETR-ND | ||
| Line 60: | Line 60: | ||
|7 | |7 | ||
|R2 thru R6 | |R2 thru R6 | ||
| − | |Reset | + | |Reset and LED load resistors |
| − | |1000 ohm | + | |1000 ohm, 1/4 W |
|Digikey | |Digikey | ||
|1.0KQBK-ND | |1.0KQBK-ND | ||
| Line 67: | Line 67: | ||
|---- | |---- | ||
|8 | |8 | ||
| − | |PROG | + | |PROG, ERROR, PULSE, HELLO |
|Indicator LED | |Indicator LED | ||
| − | |3mm | + | |3mm, Diffused Yellow |
|Evil Mad Science | |Evil Mad Science | ||
| − | | | + | |357 |
| − | | | + | |4 |
|---- | |---- | ||
|9 | |9 | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
|C1 | |C1 | ||
|Bypass Capacitor | |Bypass Capacitor | ||
| Line 106: | Line 82: | ||
|1 | |1 | ||
|---- | |---- | ||
| − | | | + | |10 |
|C2, C3 | |C2, C3 | ||
| − | | | + | |Capacitors for crystal |
| − | |18pF | + | |18pF, 50 V ceramic |
|Digikey | |Digikey | ||
|BC1004CT-ND | |BC1004CT-ND | ||
|2 | |2 | ||
|---- | |---- | ||
| − | | | + | |11 |
|XTL | |XTL | ||
|Crystal | |Crystal | ||
| − | |16 MHz | + | |16 MHz |
|Digikey | |Digikey | ||
|XC1721-ND | |XC1721-ND | ||
|1 | |1 | ||
|---- | |---- | ||
| − | | | + | |12 |
|U1 | |U1 | ||
| − | |ZIF Socket | + | |ZIF Dip Socket |
| − | |28 pin | + | |28 pin, 0.3" pin spacing |
|Evil Mad Science | |Evil Mad Science | ||
|212 | |212 | ||
|1 | |1 | ||
|---- | |---- | ||
| − | | | + | |13 |
| − | | | + | | n/a |
|PCB | |PCB | ||
|PCB for ISP Shield | |PCB for ISP Shield | ||
Revision as of 00:02, 23 March 2011
Bill of Materials
| Line | Ref Des | Description | Type | Vendor | Vendor Part Number | Quantity |
| 1 | J1 thru J4 | Header set, 6-pin (2 pcs), 8-pin (2 pcs) | Stacking type header, 0.1” spacing | Evil Mad Science | 633 | 1 |
| 2 | J5 | Target Power Enable, Header | 3 pin right-angle header, 0.1” spacing | Digikey | TSW-103-25-F-SRA-ND | 1 |
| 3 | J5 (header) | Target Power Enable, Jumper | 2 pin jumper block, 0.1” spacing | Digikey | A26242-ND | 1 |
| 4 | S1 | Reset Switch | Tactile pushbutton switch | Digikey | 679-2452-ND | 1 |
| 5 | ISP6 | 6 pin ISP Header | 2x3 pin 0.1” spaced DIL header | Digikey | 609-3202-ND | 1 |
| 6 | R1 | Reset line pull-up resistor | 10k, 1/6 W | Digikey | 10KETR-ND | 1 |
| 7 | R2 thru R6 | Reset and LED load resistors | 1000 ohm, 1/4 W | Digikey | 1.0KQBK-ND | 5 |
| 8 | PROG, ERROR, PULSE, HELLO | Indicator LED | 3mm, Diffused Yellow | Evil Mad Science | 357 | 4 |
| 9 | C1 | Bypass Capacitor | 0.1uF Capacitor | Digikey | BC1148TR-ND | 1 |
| 10 | C2, C3 | Capacitors for crystal | 18pF, 50 V ceramic | Digikey | BC1004CT-ND | 2 |
| 11 | XTL | Crystal | 16 MHz | Digikey | XC1721-ND | 1 |
| 12 | U1 | ZIF Dip Socket | 28 pin, 0.3" pin spacing | Evil Mad Science | 212 | 1 |
| 13 | n/a | PCB | PCB for ISP Shield | Evil Mad Science | 681 | 1 |
