Difference between revisions of "ISP Shield 2 Assembly Instructions"
From Evil Mad Scientist Wiki
(Created page with "This page walks through the basic assembly process for building the [http://wiki.evilmadscience.com/ISP_Shield_2.0 ISP Shield 2.0]. http://evilmadscience.s3.amazonaws.com/catalo...") |
m |
||
| Line 1: | Line 1: | ||
This page walks through the basic assembly process for building the [http://wiki.evilmadscience.com/ISP_Shield_2.0 ISP Shield 2.0]. | This page walks through the basic assembly process for building the [http://wiki.evilmadscience.com/ISP_Shield_2.0 ISP Shield 2.0]. | ||
| − | |||
| − | |||
| − | |||
== Bill of Materials, or, "What's in the kit?" == | == Bill of Materials, or, "What's in the kit?" == | ||
Revision as of 17:16, 12 May 2011
This page walks through the basic assembly process for building the ISP Shield 2.0.
Bill of Materials, or, "What's in the kit?"
| Line | Ref Des | Description | Type | Vendor | Vendor Part Number | Quantity |
| 1 | n/a | PCB for ISP Shield 2.0 | Printed circuit board | Evil Mad Science | 681 | 1 |
| 2 | R1 | Reset line pull-up resistor | 10k, 1/6 W | Digikey | 10KETR-ND | 1 |
| 3 | R2 thru R6 | Reset and LED load resistors | 1000 ohm, 1/4 W | Digikey | 1.0KQBK-ND | 5 |
| 4 | R7 | Auto-reset overrride resistor | 100 ohm, 1/4 W | Digikey | 100QBK-ND | 1 |
| 5 | J5, J6 | Target Power Enable, Auto-Reset Overrride (Header) | 6 pin right-angle header, 0.1” spacing | Digikey | SAM1043-06-ND | 1 |
| 6 | PROG, ERROR, PULSE, HELLO | Indicator LED | 3mm, Diffused Yellow | Evil Mad Science | 357 | 4 |
| 7 | XTL | Crystal | 16 MHz | Digikey | XC1721-ND | 1 |
| 8 | C2, C3 | Capacitors for crystal | 18pF, 50 V ceramic | Digikey | BC1004CT-ND | 2 |
| 9 | C1 | Bypass Capacitor | 0.1uF Capacitor | Digikey | BC1148TR-ND | 1 |
| 10 | S1 | Reset Switch | Tactile pushbutton switch | Digikey | 679-2452-ND | 1 |
| 11 | ISP6 | 6 pin ISP Header | 2x3 pin 0.1” spaced DIL header | Digikey | 609-3202-ND | 1 |
| 12 | J1 thru J4 | Header set, 6-pin (2 pcs), 8-pin (2 pcs) | Stacking type header, 0.1” spacing | Evil Mad Science | 633 | 1 |
| 13 | U1 | ZIF DIP Socket | 28 pin, 0.3" pin spacing | Evil Mad Science | 212 | 1 |
| 14 | J5, J6 (jumper) | Target Power Enable, Auto-Reset Override (Jumper) | 2 pin jumper block, 0.1” spacing | Digikey | A26242-ND | 2 |
Assembly procedure
We'll go line by line through the kit components. This guide assumes that you have had some soldering experience. If not, or it's been a while, you may also want to look at pages 2 and 5-7 of the Bulbdial clock assembly instructions, which go over basic tools and technique. And, if you really are a beginner, there are plenty of good tutorials on line, like this one.
(Assembly instructions will be here soon!)
