Difference between revisions of "Breadboard Menorah Alternate Build"
From Evil Mad Scientist Wiki
| Line 1: | Line 1: | ||
Alternate build notes for the breadboard menorah with the shamash on the end. Read through prior to bending any resistors or jumpers! | Alternate build notes for the breadboard menorah with the shamash on the end. Read through prior to bending any resistors or jumpers! | ||
| − | In | + | In Step 2 |
* One of the 0.5” jumpers should be left straight and unclipped | * One of the 0.5” jumpers should be left straight and unclipped | ||
| − | * One more of the 0.5” jumpers should be made 0.7” instead | + | * One more of the 0.5” jumpers should be made 0.7” instead |
| − | * Use a clipped lead from one of the resistors (ideally from one trimmed to the 0.4” length) to make an extra 0.4” jumper (which will look like a staple) | + | * Use a clipped lead from one of the resistors (ideally from one trimmed to the 0.4” length) to make an extra 0.4” jumper (which will look like a staple) |
| − | * The 51 ohm resistor gets bent in a U-shape | + | * The 51 ohm resistor gets bent in a U-shape |
In step 3C | In step 3C | ||
* the switch goes in row i (instead of j) from 30 to 33 | * the switch goes in row i (instead of j) from 30 to 33 | ||
| + | |||
| + | |||
| + | In step 3E | ||
| + | * The extra 0.7” jumper goes from 50 f to 55 c | ||
| + | * Use extra 0.4” jumper goes from 32 j to the lower blue stripe | ||
| + | * The 51 ohm resistor goes from 31 c to 32 c | ||
In step 4 | In step 4 | ||
| − | * Prepare a Red LED | + | * Prepare a Red LED according to the Yellow LED instructions, but instead twisting one zero-ohm jumper to each leg. On the long lead, place the body of the jumper slightly lower so that you can tell them apart. Insert from 55 a (long lead) to the blue stripe (short lead). |
In Step 5 | In Step 5 | ||
* The Yellow LED goes from 31 a to the blue stripe | * The Yellow LED goes from 31 a to the blue stripe | ||
Revision as of 18:25, 17 November 2013
Alternate build notes for the breadboard menorah with the shamash on the end. Read through prior to bending any resistors or jumpers!
In Step 2
- One of the 0.5” jumpers should be left straight and unclipped
- One more of the 0.5” jumpers should be made 0.7” instead
- Use a clipped lead from one of the resistors (ideally from one trimmed to the 0.4” length) to make an extra 0.4” jumper (which will look like a staple)
- The 51 ohm resistor gets bent in a U-shape
In step 3C
- the switch goes in row i (instead of j) from 30 to 33
In step 3E
- The extra 0.7” jumper goes from 50 f to 55 c
- Use extra 0.4” jumper goes from 32 j to the lower blue stripe
- The 51 ohm resistor goes from 31 c to 32 c
In step 4
- Prepare a Red LED according to the Yellow LED instructions, but instead twisting one zero-ohm jumper to each leg. On the long lead, place the body of the jumper slightly lower so that you can tell them apart. Insert from 55 a (long lead) to the blue stripe (short lead).
In Step 5
- The Yellow LED goes from 31 a to the blue stripe
