Editing AYAB KH-900
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.
The edit can be undone.
Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision | Your text | ||
Line 1: | Line 1: | ||
{{AYABDocs}} | {{AYABDocs}} | ||
− | + | == Introduction == | |
− | |||
− | == | ||
− | |||
This page contains documentation about how to physically connect your AYAB Interface to your knitting machine. | This page contains documentation about how to physically connect your AYAB Interface to your knitting machine. | ||
Line 11: | Line 8: | ||
− | == | + | == Installation instructions == |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
<img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/900-closed@2x.jpg" width="800" height="316" > | <img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/900-closed@2x.jpg" width="800" height="316" > | ||
This is the Brother KH-900 knitting machine. Remove the two screws on top of the machine that hold the right part of the top cover in place. | This is the Brother KH-900 knitting machine. Remove the two screws on top of the machine that hold the right part of the top cover in place. | ||
− | |||
<img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/900-cover@2x.jpg" width="800" height="387" > | <img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/900-cover@2x.jpg" width="800" height="387" > | ||
After removing those screws, the right part of the top cover can be lifted out of place. | After removing those screws, the right part of the top cover can be lifted out of place. | ||
− | |||
<img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/900-cover2@2x.jpg" width="800" height="463" > | <img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/900-cover2@2x.jpg" width="800" height="463" > | ||
Line 42: | Line 23: | ||
All of the multiwire cables can easily be disconnected. However, one green "ground" wire remains. | All of the multiwire cables can easily be disconnected. However, one green "ground" wire remains. | ||
− | |||
<img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/900-cover3@2x.jpg" width="800" height="378" > | <img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/900-cover3@2x.jpg" width="800" height="378" > | ||
− | As for that last "ground" wire, you can either leave it connected (in which case the original cover sits awkwardly held by that wire) or unscrew the lug that holds it in place. | + | As for that last "ground" wire, you can either leave it connected (in which case the original cover sits awkwardly held by that wire) or unscrew the lug that holds it in place. |
− | + | <img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/900-shield@2x.jpg" width="800" height="237" > | |
+ | <img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/shield-back@2x.jpg" width="800" height="274" > | ||
− | + | The AYAB Interface comes with two plastic covers for the circuit board, as well as cable ties to hold them in place. | |
− | + | These covers have laser-cut openings that expose only the connectors that you will need with the KH-900. There is a different cover for the front and back. The cover for the front has five openings for the connectors as well as a window for the name of the board, and the back side has openings for the power and USB ports. | |
− | + | Fit the two covers into place, and loosely attach them to the board with the cable ties. | |
− | + | <img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/shield-back@2x.jpg" width="800" height="274" > | |
− | |||
− | |||
− | <img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/ | ||
− | |||
<img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/900-complete@2x.jpg" width="800" height="243" > | <img src="http://cdn.evilmadscientist.com/wiki/ayab/installation/900-complete@2x.jpg" width="800" height="243" > | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− |