Editing Art Controller Assembly Instructions

Jump to: navigation, search

Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision Your text
Line 1: Line 1:
−
This page is part of the documentation for the '''[[Art Controller]]''' kit.
 
−
 
 
== Assembly procedure ==
 
== Assembly procedure ==
  
Line 8: Line 6:
  
  
−
=== 0.  The Art Controller kit ===
+
=== 0.  The simple relay shield kit ===
  
 
Here are all the components that make up the kit:
 
Here are all the components that make up the kit:
Line 14: Line 12:
 
http://shop.emscdn.com/wiki/artcontrol/11.jpg
 
http://shop.emscdn.com/wiki/artcontrol/11.jpg
  
 +
We'll be adding components to the various locations labeled on the board.
  
−
You can also go to the [[Art_Controller_Bill_of_Materials|Bill of Materials]] for the full list and quantities. We'll be adding components to the various locations labeled on the circuit board.
 
  
−
 
+
=== 1. Install the three 1k ohm resistors ===
−
=== 1. First step: Install the three 1k ohm resistors ===
 
  
 
http://shop.emscdn.com/wiki/artcontrol/14.jpg
 
http://shop.emscdn.com/wiki/artcontrol/14.jpg
  
−
 
+
The 1k ohm resistors will be installed in location R1, R2 and R3. Shown here:
−
The 1k resistors will be installed in location R1, R2 and R3, which are shown here:
 
  
 
http://shop.emscdn.com/wiki/artcontrol/15.jpg
 
http://shop.emscdn.com/wiki/artcontrol/15.jpg
−
 
  
 
http://shop.emscdn.com/wiki/artcontrol/16.jpg
 
http://shop.emscdn.com/wiki/artcontrol/16.jpg
−
 
  
 
First, bend the resistor leads as shown:
 
First, bend the resistor leads as shown:
Line 35: Line 29:
 
http://shop.emscdn.com/wiki/relayshield/assy_v1/4.jpg
 
http://shop.emscdn.com/wiki/relayshield/assy_v1/4.jpg
  
−
 
+
Insert the first resistor in location R1 (Resistors are not directional and can be installed either way). You can bend the leads outward to keep the resistor in place while soldering. Solder both leads.
−
Insert the first resistor in location R1. (Resistors are not directional and can be installed either way.) Once you've inserted it at the circuit board, push it flush to the surface. Then, bend the leads outward to keep the resistor in place while soldering. Solder both leads.
 
−
 
 
  
 
Make sure you have a good solder joint from the PCB pad to the resistor lead. The solder joint should be shiny without too much excess solder.
 
Make sure you have a good solder joint from the PCB pad to the resistor lead. The solder joint should be shiny without too much excess solder.
  
−
http://shop.emscdn.com/wiki/artcontrol/18b.jpg
+
http://shop.emscdn.com/wiki/artcontrol/18.jpg
  
−
 
+
Clip the excess leads short on the back side. Then, install the second and third 1k ohm resistors at locations R2 and R3, in the same manner. Again, solder both pins and clip the excess leads short.
−
On the back side of the board, clip the excess leads short. Then, install the other two 1 k resistors at locations R2 and R3, in the same manner. Again, solder both pins and clip the excess leads short.
 
  
  
Line 51: Line 42:
 
http://shop.emscdn.com/wiki/artcontrol/17.jpg
 
http://shop.emscdn.com/wiki/artcontrol/17.jpg
  
 +
The diodes will be installed in locations D1 and D2, as shown here:
  
−
The diodes will be installed in locations D1 and D2. Again bend the leads as shown:
+
http://shop.emscdn.com/wiki/artcontrol/18.jpg
 +
 
 +
http://shop.emscdn.com/wiki/artcontrol/19.jpg
 +
 
 +
Again bend the leads as shown:
  
 
http://shop.emscdn.com/wiki/relayshield/assy_v1/15.jpg
 
http://shop.emscdn.com/wiki/relayshield/assy_v1/15.jpg
−
 
  
 
Install the diodes in positions D1 and D2. Diodes have polarity - be sure to match the stripes on the diode with the stripe on the PCB.
 
Install the diodes in positions D1 and D2. Diodes have polarity - be sure to match the stripes on the diode with the stripe on the PCB.
  
 
http://shop.emscdn.com/wiki/artcontrol/20.jpg
 
http://shop.emscdn.com/wiki/artcontrol/20.jpg
−
 
  
 
Just as we did with the resistors, bend the leads outward so they stay in place during soldering. Solder. Check for a good solder connection, then clip the excess leads.
 
Just as we did with the resistors, bend the leads outward so they stay in place during soldering. Solder. Check for a good solder connection, then clip the excess leads.
Line 68: Line 62:
  
 
http://shop.emscdn.com/wiki/artcontrol/22.jpg
 
http://shop.emscdn.com/wiki/artcontrol/22.jpg
−
 
  
 
The 0.1 uF capacitors will be installed in locations C2, C3 and C4, as shown here:
 
The 0.1 uF capacitors will be installed in locations C2, C3 and C4, as shown here:
  
 
http://shop.emscdn.com/wiki/artcontrol/23.jpg
 
http://shop.emscdn.com/wiki/artcontrol/23.jpg
−
 
  
 
These are not directional and can be installed ether way. Just as before, bend the leads outward to hold the capacitor in place, solder and clip the excess leads.
 
These are not directional and can be installed ether way. Just as before, bend the leads outward to hold the capacitor in place, solder and clip the excess leads.
Line 82: Line 74:
 
http://shop.emscdn.com/wiki/artcontrol/24.jpg
 
http://shop.emscdn.com/wiki/artcontrol/24.jpg
  
−
 
+
The LED will be installed in locations D3 and D4, shown here:
−
The LEDs will be installed in locations D3 and D4, shown here:
 
  
 
http://shop.emscdn.com/wiki/artcontrol/25.jpg
 
http://shop.emscdn.com/wiki/artcontrol/25.jpg
−
 
  
 
http://shop.emscdn.com/wiki/artcontrol/26.jpg
 
http://shop.emscdn.com/wiki/artcontrol/26.jpg
−
 
  
 
Orientation is important: the ''long lead'' goes into the ''square hole''.   
 
Orientation is important: the ''long lead'' goes into the ''square hole''.   
  
−
Insert the LED. Before soldering, you can bend the leads out at 45 degrees to hold an LED in place while you solder. Solder both leads and clip the leads short on the back side.
+
Insert the LED but before soldering, you can bend the leads out at 45 degrees to hold an LED in place while you solder. Solder both leads and clip the leads short.
−
 
 
−
 
 
−
Here's what one of the LEDs looks like, soldered into place:
 
−
 
 
−
http://shop.emscdn.com/wiki/artcontrol/32.jpg
 
  
  
Line 104: Line 88:
  
 
http://shop.emscdn.com/wiki/artcontrol/27.jpg
 
http://shop.emscdn.com/wiki/artcontrol/27.jpg
−
 
  
 
The 10 uF, 50 V electrolytic capacitor will go in location C1:
 
The 10 uF, 50 V electrolytic capacitor will go in location C1:
Line 110: Line 93:
 
http://shop.emscdn.com/wiki/artcontrol/28.jpg
 
http://shop.emscdn.com/wiki/artcontrol/28.jpg
  
−
 
+
This capacitor has polarity. It must be installed with the minus on the cap to the minus on the PCB.
−
Be careful, because there is a second, similar looking capacitor that you'll install in the next step. This one is labeled "10 uF 50 V."
 
−
 
 
−
This type of capacitor has a polarity, and needs to be installed with the correct orientation. It must be installed with the minus sign ("-") on the side of the capacitor oriented towards the minus sign on the PCB.
 
−
 
 
  
 
http://shop.emscdn.com/wiki/relayshield/assy_v1/21.jpg
 
http://shop.emscdn.com/wiki/relayshield/assy_v1/21.jpg
  
 +
Also, noting polarity, the 100 uF, 10 V electrolytic capacitor in location C5, as shown here:
  
−
Also, noting polarity, install the other electrolytic capacitor (100 uF, 10 V) in location C5, as shown here:
+
http://shop.emscdn.com/wiki/artcontrol/29.jpg
−
 
 
−
http://shop.emscdn.com/wiki/artcontrol/29b.jpg
 
−
 
 
−
 
 
−
As before, pay careful attention to the polarity.  Insert, bend the leads outward, solder, and clip.
 
  
 +
Just as before, bend the leads outward, solder, and clip.
  
 
The board so far:
 
The board so far:
Line 136: Line 112:
  
 
http://shop.emscdn.com/wiki/artcontrol/31.jpg
 
http://shop.emscdn.com/wiki/artcontrol/31.jpg
−
 
  
 
The transistor will be installed in Q1, here:
 
The transistor will be installed in Q1, here:
Line 142: Line 117:
 
http://shop.emscdn.com/wiki/artcontrol/32.jpg
 
http://shop.emscdn.com/wiki/artcontrol/32.jpg
  
−
 
+
Match the flat of the transistor to the flat on the PCB. The transistor will not sit flush but you can still bend the two outer legs to keep in place for soldering. Again, solder and clip the excess leads.
−
Match the flat of the transistor to the flat on the PCB. The transistor will not sit all the way flush to the circuit board, but you can still bend the two outer legs to keep in place for soldering. Again, solder and clip the excess leads.
 
  
  
Line 150: Line 124:
 
http://shop.emscdn.com/wiki/artcontrol/33.jpg
 
http://shop.emscdn.com/wiki/artcontrol/33.jpg
  
−
 
+
The regulator will be installed in U1:
−
Install the regulator installed at location U1:
 
  
 
http://shop.emscdn.com/wiki/artcontrol/34.jpg
 
http://shop.emscdn.com/wiki/artcontrol/34.jpg
  
−
 
+
Bend the legs of the regulator back 45 degrees and place in location U1. Make certain that the back (silver side) of the regulator sits flush to the PCB and that the screw holes line up. Install the screw (item 10) and the kep nut (item 11) to hold the regulator in place. Solder and clip the excess leads.
−
In this step, you will bend the legs of the regulator back 90 degrees and place in location U1. Before you bend, see where it goes: Make certain that the back (flat, silver side) of the regulator sits flush to the PCB and that the screw hole on the regulator lines up to the one on the circuit board. 
 
−
 
 
−
 
 
−
http://shop.emscdn.com/wiki/artcontrol/51.jpg
 
−
 
 
−
Once you've bent the leads and inserted it, install the screw (item 10) and the kep nut-- a hex nut with integral lock washer, (item 11) --to hold the regulator in place. Tighten it well; the circuit board acts as a heat sink for the regulator, which can get very hot otherwise, and the screw ensures good contact to the board.  Finally, solder the three pins and clip the excess leads.
 
−
 
 
−
The photo above shows what the regulator looks like on the completed board, screwed down into place and soldered. 
 
  
  
Line 170: Line 135:
 
http://shop.emscdn.com/wiki/artcontrol/35.jpg
 
http://shop.emscdn.com/wiki/artcontrol/35.jpg
  
 +
The header will be installed in J4, here:
  
−
The 6-pin programming header will be installed in J4, shown here:
+
http://shop.emscdn.com/wiki/artcontrol/36.jpg
−
 
 
−
http://shop.emscdn.com/wiki/artcontrol/36b.jpg
 
  
−
 
+
To add these, we recommend inserting the header and then resting the board-- upside down --on the header. Solder 'tack' one leg and verify that the header sits flush to the board before soldering the remaining pins.
−
While this component is installed from the top side of the board (and with the short pins facing down into the board), we recommend inserting the header (from the top) and then resting the board-- upside down --on the header to hold it in place while you solder.  
 
−
 
 
−
 
 
−
Rather than soldering all 6 pins at once, first solder 'tack' one leg as shown below:
 
  
 
http://shop.emscdn.com/wiki/artcontrol/37.jpg
 
http://shop.emscdn.com/wiki/artcontrol/37.jpg
  
−
(The view above shows the header at J4, from the underside of the board, with one of the pins soldered.)
+
For the DIP socket, shown here:
−
 
 
−
Once you have soldered that one pin, verify that the header sits flush to the board before soldering the other five pins.
 
−
 
 
−
 
 
−
 
 
−
The DIP socket is shown here:
 
  
 
http://shop.emscdn.com/wiki/artcontrol/38.jpg
 
http://shop.emscdn.com/wiki/artcontrol/38.jpg
  
 +
Install in the location marked ATtiny2313, make sure the half-moon of the socket matches that of the PCB.
  
−
Note that it has, at one end, a small "half moon" indentation that marks its polarity. Install it in the location marked ATtiny2313, make sure the half-moon at the socket end lines up with the one on the circuit board.
+
http://shop.emscdn.com/wiki/artcontrol/39.jpg
  
−
http://shop.emscdn.com/wiki/artcontrol/39b.jpg
+
Similar to the header, turn the PCB over and tack one end pin of each first and check to see that the socket is flush to the PCB before soldering the remainder of the pins:
−
 
 
−
 
 
−
As with the header, turn the PCB over and tack one end pin of each first and check to see that the socket is flush to the PCB before soldering the remainder of the pins:
 
  
 
http://shop.emscdn.com/wiki/artcontrol/40.jpg
 
http://shop.emscdn.com/wiki/artcontrol/40.jpg
Line 208: Line 160:
 
http://shop.emscdn.com/wiki/artcontrol/41.jpg
 
http://shop.emscdn.com/wiki/artcontrol/41.jpg
  
−
This is the 8-position DIP ("dual inline package") switch.  We will install it on the circuit board in the location shown below, covering up the text on the board that says "Jumper across to select delay" :
+
The DIP switch gets mounted here:
  
 
http://shop.emscdn.com/wiki/artcontrol/42.jpg
 
http://shop.emscdn.com/wiki/artcontrol/42.jpg
  
−
http://shop.emscdn.com/wiki/artcontrol/52.jpg
+
It is not directional. However, our recommendation would be to place the '1' of the DIP switch closest to the big '-' (minus) sign on the PCB. Similar to the header and socket, tack one pin, verify the DIP switch sits flush before soldering the remainder of the pins.
  
−
Orient the DIP switch as shown above, such that the lettering is right-side up when you can read the text above it (Time Delay," "Seconds").
 
  
−
Similar to the header and socket, tack one pin, verify the DIP switch sits flush before soldering the remainder of the pins.
+
=== 11. The terminal block ===
−
 
 
−
(''Aside:'' Technically, the DIP switch is optional. To hardwire the timing, you can run wires from a given timing position (say, the 4-second position) to the opposite ground pin, to permanently configure the timing.  If you are building a lot of Art Controller units, each with fixed timing, you'll save a lot of time by running individual wires rather than installing the full DIP switch.)
 
−
 
 
−
 
 
−
 
 
−
=== 10. The terminal blocks ===
 
  
 
http://shop.emscdn.com/wiki/artcontrol/43.jpg
 
http://shop.emscdn.com/wiki/artcontrol/43.jpg
−
 
  
 
The green two-pin terminal blocks go in locations J1 and J2 -- with the holes facing outward:
 
The green two-pin terminal blocks go in locations J1 and J2 -- with the holes facing outward:
  
 
http://shop.emscdn.com/wiki/artcontrol/44.jpg
 
http://shop.emscdn.com/wiki/artcontrol/44.jpg
−
 
  
 
http://shop.emscdn.com/wiki/artcontrol/45.jpg
 
http://shop.emscdn.com/wiki/artcontrol/45.jpg
  
−
 
+
Tack one of the pins to keep the component in place, turn the board over and check that the terminal block is straight and flush with the PCB before soldering the other pins.
−
Tack one of the pins to keep the component in place, turn the board over and check that the terminal block is straight and flush with the PCB before soldering the other pins.  
 
−
 
 
−
(The pins of these terminal blocks are short and stiff.  They can't be bent out at 45 degrees to hold them in place while soldering, and generally do not need to be trimmed after soldering.)
 
−
 
 
−
 
 
−
 
 
−
http://shop.emscdn.com/wiki/artcontrol/53.jpg
 
−
 
 
−
In the photo above, of the completed Art Controller, you can see how these two two-pin terminal blocks look when installed correctly.
 
−
 
 
−
 
 
  
 
http://shop.emscdn.com/wiki/artcontrol/46.jpg
 
http://shop.emscdn.com/wiki/artcontrol/46.jpg
Line 253: Line 185:
 
http://shop.emscdn.com/wiki/artcontrol/47.jpg
 
http://shop.emscdn.com/wiki/artcontrol/47.jpg
  
 +
Repeat the procedure from the green terminal blocks.
  
−
http://shop.emscdn.com/wiki/artcontrol/51.jpg
 
  
−
To install it, repeat the procedure above from the green terminal blocks.
+
=== 12. The relay ===
−
The photo above shows how the 3-pin terminal block looks like on the completed board.
 
  
−
 
+
Finally, add the relay (It can only go in one way), and solder in place:  
−
 
 
−
 
 
−
=== 11. The relay ===
 
−
 
 
−
Finally, add the relay (it can only go one way):
 
  
 
http://shop.emscdn.com/wiki/artcontrol/48.jpg
 
http://shop.emscdn.com/wiki/artcontrol/48.jpg
  
 +
That's it for soldering!
  
−
And solder in place, here:
+
The final step is to insert the microcontroller. Be sure to orient the chip so the half-moon matches that of the socket and PCB.
−
 
 
−
http://shop.emscdn.com/wiki/artcontrol/49.jpg
 
−
 
 
−
 
 
−
(And, that's the last soldering step.)
 
−
 
 
−
=== 12. Insert IC ===
 
−
 
 
−
 
 
−
http://shop.emscdn.com/wiki/artcontrol/53.jpg
 
−
 
 
−
The final step is to insert the microcontroller into its socket. Note that it may be either an ATtiny2313 or ATtiny4313. Orientation is critical: Make sure that the half-moon indentation at one end of the chip matches that on the socket and PCB. Insert it firmly, as far down into the socket as it will go.
 
−
 
 
−
 
 
−
http://shop.emscdn.com/wiki/artcontrol/54.jpg
 
−
 
 
−
And, you're done! 
 
−
 
 
  
−
Next, head back to the main [[Art_controller|Art Controller kit]] documentation page.
+
And, you're done!  That's it!  Next, head back to the main [[Art_controller|Art Controller kit]] documentation page.

Please note that all contributions to Evil Mad Scientist Wiki are considered to be released under the GNU Free Documentation License 1.3 (see Evil Mad Scientist Wiki:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To edit this page, please answer the question that appears below (more info):

Cancel | Editing help (opens in new window)
Retrieved from "https://wiki.evilmadscientist.com/Art_Controller_Assembly_Instructions"