Editing Art Controller Assembly Instructions
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.
The edit can be undone.
Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision | Your text | ||
Line 1: | Line 1: | ||
− | |||
− | |||
== Assembly procedure == | == Assembly procedure == | ||
Line 8: | Line 6: | ||
− | === 0. The | + | === 0. The simple relay shield kit === |
Here are all the components that make up the kit: | Here are all the components that make up the kit: | ||
Line 15: | Line 13: | ||
− | + | We'll be adding components to the various locations labeled on the board. | |
− | + | === 1. Install the three 1k ohm resistors === | |
− | === 1. | ||
http://shop.emscdn.com/wiki/artcontrol/14.jpg | http://shop.emscdn.com/wiki/artcontrol/14.jpg | ||
− | + | The 1k ohm resistors will be installed in location R1, R2 and R3. Shown here: | |
− | The 1k resistors will be installed in location R1, R2 and R3 | ||
http://shop.emscdn.com/wiki/artcontrol/15.jpg | http://shop.emscdn.com/wiki/artcontrol/15.jpg | ||
− | |||
http://shop.emscdn.com/wiki/artcontrol/16.jpg | http://shop.emscdn.com/wiki/artcontrol/16.jpg | ||
− | |||
First, bend the resistor leads as shown: | First, bend the resistor leads as shown: | ||
Line 35: | Line 29: | ||
http://shop.emscdn.com/wiki/relayshield/assy_v1/4.jpg | http://shop.emscdn.com/wiki/relayshield/assy_v1/4.jpg | ||
− | + | Insert the first resistor in location R1 (Resistors are not directional and can be installed either way). You can bend the leads outward to keep the resistor in place while soldering. Solder both leads. | |
− | Insert the first resistor in location R1 | ||
− | |||
Make sure you have a good solder joint from the PCB pad to the resistor lead. The solder joint should be shiny without too much excess solder. | Make sure you have a good solder joint from the PCB pad to the resistor lead. The solder joint should be shiny without too much excess solder. | ||
− | http://shop.emscdn.com/wiki/artcontrol/ | + | http://shop.emscdn.com/wiki/artcontrol/18.jpg |
− | + | Clip the excess leads short on the back side. Then, install the second and third 1k ohm resistors at locations R2 and R3, in the same manner. Again, solder both pins and clip the excess leads short. | |
− | |||
Line 51: | Line 42: | ||
http://shop.emscdn.com/wiki/artcontrol/17.jpg | http://shop.emscdn.com/wiki/artcontrol/17.jpg | ||
+ | The diodes will be installed in locations D1 and D2, as shown here: | ||
− | + | http://shop.emscdn.com/wiki/artcontrol/18.jpg | |
+ | |||
+ | http://shop.emscdn.com/wiki/artcontrol/19.jpg | ||
+ | |||
+ | Again bend the leads as shown: | ||
http://shop.emscdn.com/wiki/relayshield/assy_v1/15.jpg | http://shop.emscdn.com/wiki/relayshield/assy_v1/15.jpg | ||
− | |||
Install the diodes in positions D1 and D2. Diodes have polarity - be sure to match the stripes on the diode with the stripe on the PCB. | Install the diodes in positions D1 and D2. Diodes have polarity - be sure to match the stripes on the diode with the stripe on the PCB. | ||
http://shop.emscdn.com/wiki/artcontrol/20.jpg | http://shop.emscdn.com/wiki/artcontrol/20.jpg | ||
− | |||
Just as we did with the resistors, bend the leads outward so they stay in place during soldering. Solder. Check for a good solder connection, then clip the excess leads. | Just as we did with the resistors, bend the leads outward so they stay in place during soldering. Solder. Check for a good solder connection, then clip the excess leads. | ||
Line 68: | Line 62: | ||
http://shop.emscdn.com/wiki/artcontrol/22.jpg | http://shop.emscdn.com/wiki/artcontrol/22.jpg | ||
− | |||
The 0.1 uF capacitors will be installed in locations C2, C3 and C4, as shown here: | The 0.1 uF capacitors will be installed in locations C2, C3 and C4, as shown here: | ||
http://shop.emscdn.com/wiki/artcontrol/23.jpg | http://shop.emscdn.com/wiki/artcontrol/23.jpg | ||
− | |||
These are not directional and can be installed ether way. Just as before, bend the leads outward to hold the capacitor in place, solder and clip the excess leads. | These are not directional and can be installed ether way. Just as before, bend the leads outward to hold the capacitor in place, solder and clip the excess leads. | ||
Line 82: | Line 74: | ||
http://shop.emscdn.com/wiki/artcontrol/24.jpg | http://shop.emscdn.com/wiki/artcontrol/24.jpg | ||
− | + | The LED will be installed in locations D3 and D4, shown here: | |
− | The | ||
http://shop.emscdn.com/wiki/artcontrol/25.jpg | http://shop.emscdn.com/wiki/artcontrol/25.jpg | ||
− | |||
http://shop.emscdn.com/wiki/artcontrol/26.jpg | http://shop.emscdn.com/wiki/artcontrol/26.jpg | ||
− | |||
Orientation is important: the ''long lead'' goes into the ''square hole''. | Orientation is important: the ''long lead'' goes into the ''square hole''. | ||
− | Insert the LED | + | Insert the LED but before soldering, you can bend the leads out at 45 degrees to hold an LED in place while you solder. Solder both leads and clip the leads short. |
− | |||
− | |||
− | |||
− | |||
− | |||
Line 104: | Line 88: | ||
http://shop.emscdn.com/wiki/artcontrol/27.jpg | http://shop.emscdn.com/wiki/artcontrol/27.jpg | ||
− | |||
The 10 uF, 50 V electrolytic capacitor will go in location C1: | The 10 uF, 50 V electrolytic capacitor will go in location C1: | ||
Line 110: | Line 93: | ||
http://shop.emscdn.com/wiki/artcontrol/28.jpg | http://shop.emscdn.com/wiki/artcontrol/28.jpg | ||
− | + | This capacitor has polarity. It must be installed with the minus on the cap to the minus on the PCB. | |
− | |||
− | |||
− | |||
− | |||
http://shop.emscdn.com/wiki/relayshield/assy_v1/21.jpg | http://shop.emscdn.com/wiki/relayshield/assy_v1/21.jpg | ||
+ | Also, noting polarity, the 100 uF, 10 V electrolytic capacitor in location C5, as shown here: | ||
− | + | http://shop.emscdn.com/wiki/artcontrol/29.jpg | |
− | |||
− | http://shop.emscdn.com/wiki/artcontrol/ | ||
− | |||
− | |||
− | |||
+ | Just as before, bend the leads outward, solder, and clip. | ||
The board so far: | The board so far: | ||
Line 136: | Line 112: | ||
http://shop.emscdn.com/wiki/artcontrol/31.jpg | http://shop.emscdn.com/wiki/artcontrol/31.jpg | ||
− | |||
The transistor will be installed in Q1, here: | The transistor will be installed in Q1, here: | ||
Line 142: | Line 117: | ||
http://shop.emscdn.com/wiki/artcontrol/32.jpg | http://shop.emscdn.com/wiki/artcontrol/32.jpg | ||
− | + | Match the flat of the transistor to the flat on the PCB. The transistor will not sit flush but you can still bend the two outer legs to keep in place for soldering. Again, solder and clip the excess leads. | |
− | Match the flat of the transistor to the flat on the PCB. The transistor will not sit | ||
Line 150: | Line 124: | ||
http://shop.emscdn.com/wiki/artcontrol/33.jpg | http://shop.emscdn.com/wiki/artcontrol/33.jpg | ||
− | + | The regulator will be installed in U1: | |
− | |||
http://shop.emscdn.com/wiki/artcontrol/34.jpg | http://shop.emscdn.com/wiki/artcontrol/34.jpg | ||
− | + | Bend the legs of the regulator back 45 degrees and place in location U1. Make certain that the back (silver side) of the regulator sits flush to the PCB and that the screw holes line up. Install the screw (item 10) and the kep nut (item 11) to hold the regulator in place. Solder and clip the excess leads. | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
Line 170: | Line 135: | ||
http://shop.emscdn.com/wiki/artcontrol/35.jpg | http://shop.emscdn.com/wiki/artcontrol/35.jpg | ||
+ | The header will be installed in J4, here: | ||
− | + | http://shop.emscdn.com/wiki/artcontrol/36.jpg | |
− | + | To add these, we recommend inserting the header and then resting the board-- upside down --on the header. Solder 'tack' one leg and verify that the header sits flush to the board before soldering the remaining pins. | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
http://shop.emscdn.com/wiki/artcontrol/37.jpg | http://shop.emscdn.com/wiki/artcontrol/37.jpg | ||
− | + | For the DIP socket, shown here: | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
http://shop.emscdn.com/wiki/artcontrol/38.jpg | http://shop.emscdn.com/wiki/artcontrol/38.jpg | ||
+ | Install in the location marked ATtiny2313, make sure the half-moon of the socket matches that of the PCB. | ||
− | + | http://shop.emscdn.com/wiki/artcontrol/39.jpg | |
− | |||
− | http://shop.emscdn.com/wiki/artcontrol/ | ||
− | |||
− | + | Similar to the header, turn the PCB over and tack one end pin of each first and check to see that the socket is flush to the PCB before soldering the remainder of the pins: | |
http://shop.emscdn.com/wiki/artcontrol/40.jpg | http://shop.emscdn.com/wiki/artcontrol/40.jpg | ||
Line 208: | Line 160: | ||
http://shop.emscdn.com/wiki/artcontrol/41.jpg | http://shop.emscdn.com/wiki/artcontrol/41.jpg | ||
− | + | The DIP switch gets mounted here: | |
http://shop.emscdn.com/wiki/artcontrol/42.jpg | http://shop.emscdn.com/wiki/artcontrol/42.jpg | ||
− | + | It is not directional. However, our recommendation would be to place the '1' of the DIP switch closest to the big '-' (minus) sign on the PCB. Similar to the header and socket, tack one pin, verify the DIP switch sits flush before soldering the remainder of the pins. | |
− | |||
− | |||
− | |||
− | + | === 11. The terminal block === | |
− | |||
− | |||
− | |||
− | === | ||
http://shop.emscdn.com/wiki/artcontrol/43.jpg | http://shop.emscdn.com/wiki/artcontrol/43.jpg | ||
− | |||
The green two-pin terminal blocks go in locations J1 and J2 -- with the holes facing outward: | The green two-pin terminal blocks go in locations J1 and J2 -- with the holes facing outward: | ||
http://shop.emscdn.com/wiki/artcontrol/44.jpg | http://shop.emscdn.com/wiki/artcontrol/44.jpg | ||
− | |||
http://shop.emscdn.com/wiki/artcontrol/45.jpg | http://shop.emscdn.com/wiki/artcontrol/45.jpg | ||
− | + | Tack one of the pins to keep the component in place, turn the board over and check that the terminal block is straight and flush with the PCB before soldering the other pins. | |
− | Tack one of the pins to keep the component in place, turn the board over and check that the terminal block is straight and flush with the PCB before soldering the other pins. | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
http://shop.emscdn.com/wiki/artcontrol/46.jpg | http://shop.emscdn.com/wiki/artcontrol/46.jpg | ||
Line 253: | Line 185: | ||
http://shop.emscdn.com/wiki/artcontrol/47.jpg | http://shop.emscdn.com/wiki/artcontrol/47.jpg | ||
− | + | Repeat the procedure from the green terminal blocks. | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | === | + | === 12. The relay === |
Finally, add the relay (it can only go one way): | Finally, add the relay (it can only go one way): | ||
Line 268: | Line 194: | ||
http://shop.emscdn.com/wiki/artcontrol/48.jpg | http://shop.emscdn.com/wiki/artcontrol/48.jpg | ||
− | + | And solder in place: | |
− | And solder in place | ||
http://shop.emscdn.com/wiki/artcontrol/49.jpg | http://shop.emscdn.com/wiki/artcontrol/49.jpg | ||
+ | That's it for soldering! | ||
− | + | The final step is to insert the microcontroller. Be sure to orient the chip so the half-moon matches that of the socket and PCB. | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | The final step is to insert the microcontroller | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | Next, head back to the main [[Art_controller|Art Controller kit]] documentation page. | + | And, you're done! That's it! Next, head back to the main [[Art_controller|Art Controller kit]] documentation page. |