Editing Making your first plot
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.
The edit can be undone.
Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision | Your text | ||
Line 1: | Line 1: | ||
− | + | So now you have your EggBot assembled and connected, and you've installed Inkscape and the EggBot extension (and any necessary USB drivers). How do you successfully draw on your first egg using the EggBot? | |
− | |||
− | |||
− | So now you have your EggBot assembled and connected, and you've installed Inkscape and the EggBot extension (and any necessary USB drivers). How do you | ||
− | |||
− | |||
− | |||
= Using the Inkscape EggBot Control Extension = | = Using the Inkscape EggBot Control Extension = | ||
− | The EggBot Control | + | The Inkscape EggBot Control Extension is the tool that you will use to help you test and align the EggBot, as well as transfer your drawings to an egg. First you'll need to start Inkscape. Once Inkscape is running, you'll have an '''Extensions''' menu, and on that menu will be a submenu labeled '''Eggbot'''. In that submenu are several different extensions that perform various Eggbot-related tasks. By far the most important of these is the '''Eggbot Control...''' extension, which is the program that actually communicates with the Eggbot. |
− | |||
− | + | The Eggbot Control dialog has eight tabs. The first two tabs, "'''Plot'''" and "'''Setup'''" provide the basic controls to set up and use the Eggbot. The other six tabs provide a variety of | |
− | The | ||
* '''Plot''' -- This tab is used to transfer (plot) a drawing from Inkscape to the egg. | * '''Plot''' -- This tab is used to transfer (plot) a drawing from Inkscape to the egg. | ||
Line 27: | Line 19: | ||
= Prepare your EggBot for drawing on eggs = | = Prepare your EggBot for drawing on eggs = | ||
− | Your first instinct will be to put a pen in the pen arm, put an egg in the egg cups, and start drawing. '''This is an excellent way to frustrate yourself and ruin an egg.''' Instead, you want to be able to place an egg in the egg cups such that the egg is evenly aligned, and the pen | + | Your first instinct will be to put a pen in the pen arm, put an egg in the egg cups, and start drawing. '''This is an excellent way to frustrate yourself and ruin an egg.''' Instead, you want to be able to place an egg in the egg cups such that the egg is evenly aligned, and the pen arm will have firm contact with the egg as it rotates. |
To do that, follow these steps: | To do that, follow these steps: | ||
1. '''Calibrate the pen up/pen down positions'''. | 1. '''Calibrate the pen up/pen down positions'''. | ||
− | |||
− | |||
− | |||
:* This is part of the initial setup; you won't have to do this every time. | :* This is part of the initial setup; you won't have to do this every time. | ||
− | :* From the '''Setup''' tab, select "Toggle pen up/down" | + | :* From the '''Setup''' tab, select "Toggle pen up/down." Then, click apply several times. The servo motor should move back and forth between two different positions. |
:: If your servo motor does not move, check that it's connected to the right location and that the EBB has both power (from the plug in power supply) and the USB connection to your computer. | :: If your servo motor does not move, check that it's connected to the right location and that the EBB has both power (from the plug in power supply) and the USB connection to your computer. | ||
:* Adjust the two percentage values for the pen up position and pen down positions such that: | :* Adjust the two percentage values for the pen up position and pen down positions such that: | ||
Line 47: | Line 36: | ||
3. '''Set the pen arm arc depth'''. That is to say, a different setup is needed if you're printing on a sphere (like a golf ball) than if you're printing on an egg-shaped object. | 3. '''Set the pen arm arc depth'''. That is to say, a different setup is needed if you're printing on a sphere (like a golf ball) than if you're printing on an egg-shaped object. | ||
− | The pen motor mounts with screws through slots, so that the depth of its drawing arc can be changed. On the inside of the chassis sidewall, there's a gauge and some simple illustrations indicating rough positions for the motor. A chicken egg will typically use the center position; a | + | The pen motor mounts with screws through slots, so that the depth of its drawing arc can be changed. On the inside of the chassis sidewall, there's a gauge and some simple illustrations indicating rough positions for the motor. A chicken egg will typically use the center position; a round glass bulb (such as a lightbulb or decorative ball) will use the top position; a duck or goose egg may need the bottom position. Gently loosen the screws, slide the motor to the correct height, and then gently tighten the screws. |
− | 4. '''Align the headstock'''. The headstock (containing the egg motor) is connected to the | + | 4. '''Align the headstock'''. The headstock (containing the egg motor) is connected to each of the sidewalls with 3 screws. Gently loosen the screws on each side until the headstock barely slides. You'll want to slide the headstock until the equator of an egg placed against the headstock (south pole towards the headstock) is directly beneath the pen arm. Once you like the position of the headstock, set the egg aside and tighten the headstock screws on each sidewall, taking care to ensure that headstock meets each sidewall at the same place on the gauges. |
− | 5. '''Align the tailstock'''. The tailstock (containing the spring-loaded plunger) is connected to the sidewalls with screws, just like the headstock. Gently loosen the screws on each side until the tailstock barely slides. With an egg placed against the headstock egg cup, set the egg's north pole in the plunger egg cup, and then slide the tail stock until the plunger O-ring (between the two sides of the tailstock) is roughly | + | 5. '''Align the tailstock'''. The tailstock (containing the spring-loaded plunger) is connected to the sidewalls with screws, just like the headstock. Gently loosen the screws on each side until the tailstock barely slides. With an egg placed against the headstock egg cup, set the egg's north pole in the plunger egg cup, and then slide the tail stock until the plunger O-ring (between the two sides of the tailstock) is roughly in the middle. Once you like the position of the tailstock, tighten the tailstock screws on each sidewall, taking care to ensure that tailstock meets each sidewall at the same place on the side scales. |
− | 6. '''Place a pen in the pen arm'''. Uncapped, point down, (of course) so you can judge how it will align with the egg. | + | 6. '''Place a pen in the pen arm'''. Uncapped, point down, (of course) so you can judge how it will align with the egg. Tighten the thumbscrew to fix the pen position. Rotate the pen arm until it is vertical. |
− | 7. ''' | + | 7. '''Set the pen arm height'''. Place an egg between the egg cups, and a pen in the pen arm such that the pen is a few millimeters above the surface of the egg when it is in the "up" position. You may need to raise or lower the pen arm, by loosening the thumbscrew that holds the proximal pen arm to the pen arm backer. Tighten the screw when the pen is just above (several millimeters above) the egg surface. Swivel the pen arm over the egg to check clearance. |
− | |||
− | |||
Line 63: | Line 50: | ||
# Remove pen (if any) from the pen arm. | # Remove pen (if any) from the pen arm. | ||
− | # Start with a clean, dry, room-temperature, raw egg. (If | + | # Start with a clean, dry, room-temperature, raw egg. (If not an egg, it's likely to already be room temperature, dry and raw. Make sure that it's clean, too!) |
#* Dry, so your marker will adhere. | #* Dry, so your marker will adhere. | ||
#* Room-temperature, so that your egg will stay dry. | #* Room-temperature, so that your egg will stay dry. | ||
#* Raw, so that you can empty it out afterwards, in the event that you get a good one. (Yes, you could hard-boil your eggs, but then you'll have to break them to get the centers out. Or you could empty them first, but that's an awful lot of effort if an egg doesn't turn out right.) | #* Raw, so that you can empty it out afterwards, in the event that you get a good one. (Yes, you could hard-boil your eggs, but then you'll have to break them to get the centers out. Or you could empty them first, but that's an awful lot of effort if an egg doesn't turn out right.) | ||
#* Clean, so that ink flow is not affected by grease on the surface. You may even want to use rubber gloves for handling your eggs to keep greasy finger prints off (especially important if using technical pens with very fine nibs.) | #* Clean, so that ink flow is not affected by grease on the surface. You may even want to use rubber gloves for handling your eggs to keep greasy finger prints off (especially important if using technical pens with very fine nibs.) | ||
− | # Pull back the plunger and roughly center the end of the egg on the headstock. Gently return the plunger to the other end of the egg. Spin the egg to see if it is centered, and adjust its position in the two egg cups as necessary. | + | # Pull back the plunger and roughly center the end of the egg on the headstock. Gently return the plunger to the other end of the egg. Spin the egg to see if it is centered, and adjust its position in the two egg cups as necessary. |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
= Drawing on your Egg = | = Drawing on your Egg = | ||
Line 84: | Line 65: | ||
# From the '''Plot''' tab, press apply, and the EggBot should print the entire drawing. | # From the '''Plot''' tab, press apply, and the EggBot should print the entire drawing. | ||
− | + | For multiple color printing, keep different color information in separate layers of your Inkscape document named with an initial number. (e.g. 1-red, 2-black). Use the '''Layers''' tab to plot layer by layer, changing the pen between layer plots. | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− |